Hello Guest it is March 28, 2024, 07:27:09 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - wwenter

Pages: 1 2 »
1
Bargain Basement / Re: pmdx 126,107 speed control and 411 or 410 for mach 4
« on: February 05, 2018, 08:45:24 PM »
I went with the HiCon

2
Bargain Basement / pmdx 126,107 speed control and 411 or 410 for mach 4
« on: February 05, 2018, 12:55:11 AM »
I have these item for sell all work just fine I have up graded my lathe and do not need these any more $250.00 for 126,107 and 411 or 410 you pick. If interested let me know

3
Mach4 General Discussion / Re: homing to index pulse
« on: January 21, 2018, 11:25:35 PM »
Thanks Craig
All be giving them a call tomorrow

4
Mach4 General Discussion / Re: homing to index pulse
« on: January 21, 2018, 10:07:45 PM »
Hello
That is part of the reason I purchased the ess was for index pulse homing and it works very well the other reason was the ess per there literature works with mach3 and mach4 (Threading) single pulse per rev for timing and it is definitely is out of time now the uss for mach4 is still in development. I have been contact with Andy for the last month and have been told a few day to soon to now Threading is #3 on my priority list behind Support and B.C. finalization so that is why I am looking in a different direction and hoping for some help on it. I don't see ess threading soon I like the ess and it's fetchers but with out threading my lathe is no good to me. Thanks for your in put    

5
Mach4 General Discussion / homing to index pulse
« on: January 20, 2018, 12:01:30 AM »
Does Mach4 support Homing to encoder index pulse or is there a way to do it. I was using ess warp9 but the ess does not support threading for lathe using Mach4.
Thanks for any help

6
Mach4 General Discussion / Macros for lathe spindle range change
« on: July 24, 2017, 08:56:33 AM »
Hello All
Is there a macro that has been written that would allow me to enter a m41- m46 to change my lathe spindle range in a g code program for mach4
Thanks

7
Mach4 General Discussion / Re: G76 threading cycle bug ?
« on: March 05, 2017, 08:49:08 PM »
I get the same error but I can not get my machine to do any threading G76 or G32 sorry I can not be any heip

8
Mach4 General Discussion / Mach4 Threading having problems
« on: March 05, 2017, 11:12:00 AM »
Hello I am run mach4 using pmdx 126 with pmdx 410. I am setup with signal index pulse for rpm have verified rpm is correct on screen set. Machine is up and running servo are tuned and have run some tests parts and now I am trying to thread I have use the wizards in mach 4 and tried some g32 code and I  keep getting pmdx-smartbob error, rpm too great for threading any ideal what is going on

9
Mach4 General Discussion / Re: Tools values not changing
« on: February 28, 2017, 09:36:30 PM »
After you you hit cycle start you activate offset 1 do you then get a prompt that says something like a tool change has been requested via m6. Change tool then press cycle start to continue that should give you tool 1.

10
Mach4 General Discussion / Re: Tools values not changing
« on: February 28, 2017, 06:56:16 PM »
After you go in to mdi and type in t0101 your active offset 1 should show then hit cycle start should bring up tool 1.
when you enter your offset for X does the offset show in the dro as what you entered if not go to fixture offset and make sure you have all 0.000 in x. When you open tool table high light X hit set X offset close out tool table and open a gain you see a change that is how mine works

Pages: 1 2 »