Hello Guest it is August 08, 2020, 03:14:54 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - attila0216

Pages: 1 2 3 »
1
Mach Screens / Re: Screen4 Mach3 Status bar missing!
« on: September 12, 2019, 03:37:21 AM »
Actually that screen is the main screen. Unfortunatelly i can't copy and paste the hole main screen because i would ruin the other screen with that. Any other idea?

2
Mach Screens / Screen4 Mach3 Status bar missing!
« on: September 11, 2019, 06:11:47 PM »
I'M currently designing my screen for Mach3 plasma in Screen4. It is almost done, but I just can't find Status bar for error messages. Does anyone know where i can find that and paste it on my screen? Or how?
Thank you!

3
VB and the development of wizards / Re: What is wrong with this Code?
« on: September 10, 2019, 05:45:08 PM »
Ignore previous Post of mine. My mistake. Used wrong M code under button :) Works great! Big thank you!

4
VB and the development of wizards / Re: What is wrong with this Code?
« on: September 10, 2019, 05:17:15 PM »
Ok. So i have tried you Code. Unfortunatelly Mach starts to run even if not in Pause state. So ignores 805 led state. I don't know why

5
VB and the development of wizards / Re: What is wrong with this Code?
« on: September 10, 2019, 12:52:26 PM »
Thank you! I'LL GIVE A TRY TONIGHT AFTER WORK!  I'll let you know if it worked or not.

6
VB and the development of wizards / What is wrong with this Code?
« on: September 10, 2019, 05:36:13 AM »
So i have created a button in screen4 designer, for my plasma cutter if i press feedhold machine stops and torch off(brain turns off torch). Now this button suppose to watch Pause LED state and if OEMled 805 active , should start M3 code and cycle start. It does start if i press, but, unfortunatelly starts even if 805 led not active. So what am i doing wrong ?

GetOemLed 805 = 1
DoSpinCW
DoOEMbutton (1000)
 

7
SmoothStepper USB / Re: Using ESS port 3 in Mach 3
« on: June 03, 2016, 04:49:29 PM »
No unfortunatelly not. So i have hooked up this C10s to 3rd port swithes relays etc. They are working as they should, BUT when i try tojog the machine nothing works untill iunplug the C10s from the 3rd port.

8
SmoothStepper USB / Re: Using ESS port 3 in Mach 3
« on: June 03, 2016, 04:24:07 PM »
Hi Brian,

I had exactly today the same problem. With C10S BOB. After i pluged in no movement i've got. If i plug out machine moves again. So did you resolve this issue?

Thanx in advance

9
PoKeys / Re: Windows can't start up with pokeys56u plugged in
« on: April 13, 2016, 03:56:54 PM »
Yes, thank you!!!,BUT  I have tried i disabled usb boot up only my ssd enabled but still i am getting this error. But only pokeys can cause this issue, cause whenever i plug out prior to pc start, no errorrs. Any other idea?

10
PoKeys / Windows can't start up with pokeys56u plugged in
« on: April 10, 2016, 12:48:55 PM »
Good eveving to All,

I have a wierd thing with my pokeys 56u. When pokeys plugged in via usb port and i try to turn on PC windows can't start. If i unplug it, windows starts up with no problem. However ones is windows loaded and i plug in pokeys it works with no problem.
What can be the problem?

Pages: 1 2 3 »