Messages

1

Mach4 General Discussion / Re: Huanyang GT-5R5G-2 VFD control spindle on/off & Fwd/Rev Mach4

« on: May 10, 2019, 05:34:34 PM »

Thank you for the replies.

I have already done P0.01.

I'm stuck on P5.10 page 47-48.  I currently have the following connected to terminals.  Feel like I am missing something in the manual for P5.10.  I also don't understand how to set the K1 or K2 switches in the P5.10.

S1 = Forward
S2 = Reverse
AI1 = Variable Speed
AI2 = Variable Speed

Thoughts?

2

Mach4 General Discussion / Huanyang GT-5R5G-2 VFD control spindle on/off & Fwd/Rev Mach4

« on: May 09, 2019, 10:09:53 PM »

I recently was forced to upgrade my spindle which caused me to upgrade my Huanyang VFD(HY04D023B) to the Huanyang GT-5R5G-2. I am currently running Mach4 as my CNC controlling software.

I currently have the new VFD (GT-5R5G-2)directly controlling the spindle 100% with no problems from the keypad on the VFD. I am running into issues with getting MACH4 to communicate with the new VFD. I can't get Mach4 to turn spindle on/off. Does someone have the settings in mach4 for this newer VFD drive? Possibly the wiring diagram for which terminals the on/off & Fwd/Rev should be hooked to?

Currently not getting any indication from MACH4 that there is a fault. I believe there is a setting I maybe missing on the drive or one that I may have wrong.

If anyone has any suggestions would be helpful.

Thanks,

3

Finished Plugins for Download / Re: Huanyang VFD controller plugin

« on: February 23, 2014, 01:57:52 PM »

Thanks for the advice.

I completely updated windows framework to 3.5, updated the V++2010 distributable's and updated Mach to latest version R03.043.066. 
Combination of these aloud me to load the Hangyang plugin and reconfigure it.

However, now when I try to run a g-code file Mach3 will randomly freeze in the code every single time and lock the entire PC up.  Anyone have any ideas on what would be causing this?

Thanks for the help.

Mike

4

Finished Plugins for Download / Re: Huanyang VFD controller plugin

« on: February 19, 2014, 11:06:48 PM »

Did you happen to remember to download the VC 2008 redistributables?
http://www.microsoft.com/fr-fr/download/details.aspx?id=5582

Richard

Yes, I reloaded these.

5

Finished Plugins for Download / Re: Huanyang VFD controller plugin

« on: February 19, 2014, 10:46:24 PM »

I have been running the HangyangVFD plugin by Matty Zee on my CNC for the past year without any problems. I recently had a (Blue Screen of Death) from my Windows XP operating system and had to completely reinstall everything. I got everything working again but cannot get the Hangyang driver to be recognized by the Mach3 software. I get the following errors when I load Mach:

Plugin DLL Defective. Reload.

Then

HuanyangVFD.dll-Defective Plugin found..ignoring..

I cannot see the plugin at the Mach plugin config screen. I tried re-downloading the driver and erasing the old one but no dice... Anyone know how I can fix this???

I am running Mach3 version: R3.043.022
I am current on Windows XP service packs and all updates.

Thanks in advance on assistance. Need to figure this out fast as I have a couple jobs on hold because of this issue.