Messages

1

General Mach Discussion / Re: Matsuura MV-500 with Yaskawa Drives Retrofit

« on: February 16, 2014, 04:48:58 PM »

Hi Kist,

Do you have anything about CPCR-QR-CB8D
This is The Last i Need to Start rebuild

2

General Mach Discussion / Re: Matsuura MV-500 with Yaskawa Drives Retrofit

« on: February 08, 2014, 09:33:32 AM »

Hi Kist, do you have anything about thwe spindle drive? i will finish the wiring diagram.

CS LAb has an converter :-) for the Encoders
 
"Dear sir,
In our offer we have 8 - channels converter which changes unsymmetrical signal (non differential)  5V or 24V to symmetrical (differential) signal 5V.
Especially for you we can adapt it to 12V. Then you can use your current encoders."

3

General Mach Discussion / Re: Matsuura MV-500 with Yaskawa Drives Retrofit

« on: February 03, 2014, 05:51:03 PM »

Hi Kist,

do you have any idea to connect the XYZ Encoders?

regards

Olli

4

General Mach Discussion / Re: Matsuura MV-500 with Yaskawa Drives Retrofit

« on: February 03, 2014, 04:47:21 PM »

What i do last hours.

!!! it is for 230/400V !!!
it is not compleate and i can't give warranty

5

General Mach Discussion / Re: Matsuura MV-500 with Yaskawa Drives Retrofit

« on: February 03, 2014, 01:31:34 PM »

Hi,
Perfect.

Please take a Look to The spindle and spindle Drive. There i have nothing at this Moment.

Today i was happy to find out The Most for xyz drives and toolchange.
I make a new wiring Diagramm an Post it here.

Do you want clean The wiring Chaos or do you want use this?


Regards
Olli

6

General Mach Discussion / Re: Matsuura MV-500 with Yaskawa Drives Retrofit

« on: February 01, 2014, 05:32:24 AM »

Hello,
page 6 shown i/o, but this is not the same like in pdf i have attached.

the Servo drive has 4 relevant connectors.

1CN
2CN
3CN
5CN

4CN is only internal Servodrive Connection.



in TSE-C717-13E page 6 for example the Tacho is connected to 1CN-6 & 1CN-12
in Yaskawa Doc49 it is on 2CN-1 & 2CN-20

i think, later i have to check the right connector in the machine. i have no other idea to come a step forward.

7

General Mach Discussion / Re: Matsuura MV-500 with Yaskawa Drives Retrofit

« on: January 31, 2014, 01:30:21 PM »

Tanks, but this i have.  There are no Description about The connectors )-:

8

General Mach Discussion / Re: Matsuura MV-500 with Yaskawa Drives Retrofit

« on: January 31, 2014, 06:47:50 AM »

WOW you are terrific.
thanks a lot !!!

9

General Mach Discussion / Re: Matsuura MV-500 with Yaskawa Drives Retrofit

« on: January 31, 2014, 06:40:16 AM »

Thas correct, but the Manual you will find is the TSE-C717-12 xx and this does not match with the CPC-MR052GC axis servo drive;-(

10

General Mach Discussion / Re: Matsuura MV-500 with Yaskawa Drives Retrofit

« on: January 31, 2014, 06:04:15 AM »

from the Yaskawa drives