Messages

1

CS-Lab / Re: Problem in CSMIO IP A configuration

« on: November 02, 2015, 06:37:51 PM »

Hello

I know how to connect all buttons. I have to connect to normal CSMIO DIs and set OEM trigger code according to that DI

My question is, how should i connect encoder to CSMIO? If I connect it to Encoder number 3, should i set MACH port & Pin - MPG A+ Port 10 pin 3, MPG A- Port10 pin 3??

2

CS-Lab / Re: Problem in CSMIO IP A configuration

« on: October 27, 2015, 06:31:22 PM »

Hello Hood,

My MPG encoder is 5V signal so how can i connect it? If i connect as an input to CSMIO then it should be 24 Volt. Can i connect as an encoder input? If yes, then what setting i will need to do in MACH? I mean I know how to set DI/DO in mach but dont know about encoders.

3

CS-Lab / Problem in CSMIO IP A configuration

« on: October 24, 2015, 04:29:12 AM »

Attached is snap of the mpg diagram

What settings do i need in mach,? I never used mpg


Sent from my iPhone

4

CS-Lab / Re: Problem in CSMIO IP A configuration

« on: October 11, 2015, 01:57:35 AM »

Every thing is working as it should.

Now i have one mpg and i want to connect it with CSMIO IP/A

can i connect it directly? Is it compulsory to purchase MPG module from cs lab?

5

CS-Lab / Problem in CSMIO IP A configuration

« on: August 20, 2015, 01:36:41 PM »

Hi

I replaced encoders and now all errors gone

Taken a trials of all axis then finally tried on a sample job

Problem is x axis is shifting at one end. I mean x axis is traveling more in one direction although its a very small error but getting accumulated and being a large enough not to avoid

Can you suggest problem?

If my step pulse setting is not correct, i should have inaccurate travel but same in both directions, right?


Sent from my iPhone

6

CS-Lab / Problem in CSMIO IP A configuration

« on: August 08, 2015, 08:48:30 AM »

2) dro and mach shows motion completed. Only physical movement is not there

3) its not encoder as its same direction in mach dro also. Mach dro also moves in same direction irrespective of my command

I will post my xml as soon as i go to the machine


Sent from my iPhone

7

CS-Lab / Re: Problem in CSMIO IP A configuration

« on: August 08, 2015, 04:55:07 AM »

Ok Proper shielding made so many things working still getting that encoder error

One more issue i observed during trial is, my axis movement is less in one side

i ran x axis for say 5 mm and my encoder count goes from say 25000 to 65000 (if 4000 count for 0.5 mm or 1 revolution), when i gave reverse command then it stops physically after 3 mm movement only. At this time count is also less 41000 (it should be stopped at 25000) which shows controller asked drive to stop at 3 mm. can you suggest why?

One more problem is in MDI
i can not use MDI because it giving strange movement (same direction run whatever command i gave, not stopping at the desired location)

Is it related to CS controller?

8

CS-Lab / Re: Problem in CSMIO IP A configuration

« on: August 04, 2015, 04:39:48 AM »

Ok waiting for reply from them.

Anyways, what about other problem? Do you think its related to encode only?
My motor starts running at full speed, then i assigned empty encoder channel to that axis, then it moves slowly, i again assign original encoder and getting it working again

Is it related to encoder issue or anything else?

9

CS-Lab / Re: Problem in CSMIO IP A configuration

« on: August 04, 2015, 03:58:03 AM »

No response from cs lab yet

10

CS-Lab / Re: Problem in CSMIO IP A configuration

« on: August 04, 2015, 03:56:19 AM »

Answer is yes for all

I am getting correct count if i turn encoder/motor manually

Getting position correct all the times except for first time

Encoder shows count but with red flashing 255 values in between