Hello Guest it is March 28, 2024, 09:48:59 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - khaled

Pages: 1 2 »
1
General Mach Discussion / post processor metric for mach 3 featurecam
« on: July 13, 2015, 02:44:20 PM »
HI
Anyone know how i can get a post processsor in metric (millimetr) not inch   for featurecam To Mach3

Thankx

2
Newfangled Solutions Mach3 Wizards / Re: NFS Turn Wizard
« on: October 26, 2014, 03:23:25 PM »
I have watched youtube videos about nfs turn wizard where they are able to rotate the part on the screen so could it be some settings?

on my screen all i see in the centre to the left is tool number  on the right hand side is option change tool but nothing happens when i click the button does not turn green
here is some screenshot

3
Newfangled Solutions Mach3 Wizards / Re: NFS Turn Wizard
« on: October 26, 2014, 11:59:29 AM »
Thankx Ron

im a newbee to this i am using turn wizard both the mouse left and right  right moves the part up and side and the left key zooms and the scroll also zooms how can i change the settings so the mouse when i click it it will rotate or angle my part? when i use the mill wizard it works fine the left click rotates and right up and down scroll zooms but turn wizard does not

how would i do the tool change in the turn wizard im used to the mill sorry and the safe location?

4
Newfangled Solutions Mach3 Wizards / Re: NFS Turn Wizard
« on: October 25, 2014, 04:57:39 PM »
Hi i just purchased nfs turn wizard if i want to use the turn part i do all steps and all things are fine i would like to know how can i rotate my part on the screen and view it in 3d shadow? also would like to know when i finish the cycle i need my tool to return home but further from the part so i can change tools i dont have any limit switch please help

5
General Mach Discussion / Re: worm gear cad design
« on: December 26, 2013, 01:17:26 PM »
 ;)HI John
Thankx again for the explanation yes i have a 40:1 universal table maybe its old but i do have a VERTEX HV10 254 diameter which is 90:1 but it has a backlash which im not sure how to minimise! its mounted shaft to shaft so would the calculation 200* 90 =18000/ 360 = 50 steps per is this correct?
but my problem is this rotary table has backlash is there a way to minimise it on the table itself. i know its done on mach3 settings for backlash but dont see on the rotary table.
THANKX


6
General Mach Discussion / Re: worm gear cad design
« on: December 25, 2013, 05:15:53 PM »

The rotary ratio is 40 to 1
motor steps 200 per revolution.

7
General Mach Discussion / Re: worm gear cad design
« on: December 25, 2013, 02:43:59 PM »
The rotary ratio is 40 to 1
motor steps 200 per revolution.

8
General Mach Discussion / Re: worm gear cad design
« on: December 25, 2013, 01:08:18 PM »
Good afternoon
thankx yeh i checked it could of been alphabet that i used also and now it works with this new Gcodes
could you please advise on the Rotary table settings on the method for 'steps per'
rotary pulley 40 teeth
the motor pulley 20 teeth
how would i calculate the steps per ; velocity and motor tuning?

9
General Mach Discussion / Re: worm gear cad design
« on: December 24, 2013, 04:50:55 PM »
What a great explanation thank you i did the settings as above and i try to run the program as above
Step 1:

G0 G21 G49 G40.1 G17 G80 G50 G90 G98
and it says error in this line is there something wrong with this line of codes maybe error  on a setting
man im toubling you lots God bless you!!!!!!

10
General Mach Discussion / Re: worm gear cad design
« on: December 24, 2013, 04:50:02 PM »
What a great explanation thank you i did the settings as above and i try to run the program as above
Step 1:

G0 G21 G49 G40.1 G17 G80 G50 G90 G98
and it says error in this line is there something wrong with this line of codes maybe error  on a setting
man im toubling you lots God bless you!!!!!! ;)

Pages: 1 2 »