Messages

1

General Mach Discussion / Surely some Mach3 genus can answer this question?

« on: April 20, 2014, 06:26:05 PM »

The software workaround: 1) make sure that the Mach3 signal level is such that when there is no step, pin 5 of the TB6560 (named CLK in the datasheet) is low. 2) Use 1/2 step Sherline mode, with kernel running at 25 or 35 kHz. The effect of Sherline mode is that the pulse will stay high for the entire duration of the kernel cycle, and reset on the next cycle. 3) Set the Direction pulse timing to the maximum (15 us - note the GUI indicates 1 to 5 but it will accept up to 15). The net effect is a long pulse (40 us for 25 kHz kernel, 28.5 us for 35 kHz), with the limitation that the maximum pulse rate is reduced to one half of the kernel frequency. This is not a problem given the fact that in any case the TB6560 maximum allowable step frequency is only 15 kHz.

The hardware workaround: replace R4 to R9 with lower value (470 or 1k). This will make the rising edge sharper and gain some pulse width margin. You can't go too low with the value, otherwise the falling edge will become too slow, reducing the margin. You still need to make sure the Mach3 signal level is as in point 1 above. You can then either use Sherline mode as above, or normal mode. In the latter case, just make sure both step and direction timings are set to their maximum (15 us) and don't exceed 35 kHz (there is no point and all it will do is reduce your pulse times, this eating the margin).

There are many more subtle and less subtle problems with the board design. It really sucks, but with either workaround it can be made to at least operate without losing steps.


    How do I accomplish step one in Mach3 or can it be done at all? Simple enough right... Thanks in advance.

2

General Mach Discussion / Setting up the following statement in Mach3 for a CNC3040

« on: April 20, 2014, 03:16:05 PM »

Hi All,
   The following statements come from a post on the CNC-Zone forum. I need help accomplishing the first statement in this post as I don't have a clue even after reading enough  to choke a mule on the subject. Although I did learn some other useful stuff in the adventure I wasn't able to answer the first step in this post. Maybe someone with more brains than I have can help me out in this one hopefully. Or at least tell me it can't be done in Mach3.
   
   The software workaround: 1) make sure that the Mach3 signal level is such that when there is no step, pin 5 of the TB6560 (named CLK in the datasheet) is low. 2) Use 1/2 step Sherline mode, with kernel running at 25 or 35 kHz. The effect of Sherline mode is that the pulse will stay high for the entire duration of the kernel cycle, and reset on the next cycle. 3) Set the Direction pulse timing to the maximum (15 us - note the GUI indicates 1 to 5 but it will accept up to 15). The net effect is a long pulse (40 us for 25 kHz kernel, 28.5 us for 35 kHz), with the limitation that the maximum pulse rate is reduced to one half of the kernel frequency. This is not a problem given the fact that in any case the TB6560 maximum allowable step frequency is only 15 kHz.

The hardware workaround: replace R4 to R9 with lower value (470 or 1k). This will make the rising edge sharper and gain some pulse width margin. You can't go too low with the value, otherwise the falling edge will become too slow, reducing the margin. You still need to make sure the Mach3 signal level is as in point 1 above. You can then either use Sherline mode as above, or normal mode. In the latter case, just make sure both step and direction timings are set to their maximum (15 us) and don't exceed 35 kHz (there is no point and all it will do is reduce your pulse times, this eating the margin)

   The statement labeled number one is the puzzle for me in this. I have been unable to figure out how to accomplish what the author is saying in Mach3 about keeping the signal low to pin five in it. I have already tried a number of different solutions to my problems with the machine losing steps but at this rate it is beginning to look like a replacement controller is in my future if no one here can help me in this.

                                                                                            Thanks in advance,
                                                                                                Lindsey

3

FAQs / Fixing the defects in the YOCNC(cheap) milling/engraving machines from China

« on: December 02, 2013, 04:37:59 PM »

One of  the other members "helloagain" has figured out how to fix the controller boxes that come with most of the new cheap Chinese machines. Models include the CNC 3040 and CNC 6040 just to name a couple. Opening the controller box and looking at the parallel card in it should let you see if yours is one that can be modified to work like it should. Afer it is modified it will also allow for a USB to parallel port setup using a more modern computer to run the Mach3 software. The problems start with poor shielding and cheap wiring in them. The wiring needs to be replaced as well as some technical modifications to the parallel port board inside the controller box. Not replacing the wiring means that at some point in the near future you will be faced with dificult to diagnose problems with these machines. Basically you need to replace the three chips on the parallel port board inside the controller and replace two of them with different chips. The third one will be deleted and a jumper installed in its place. Along with grounding each input output to ground with a ceramic cap. Get the full details on how to fix yours at. http://www.cnczone.com/forums/chinese_machines/157193-experience_carving-computer-numeric-control_com_6040_router.html
As you can tell by the conversation in that link at one point YOCNC actually decides to try these modifications themselves. Spread the word as these machines problems or most of them can be solved with a little soldering, some new parts, and a little effort. All of the info can be found at the link above. If it doesn't work for you just go to www.cnczone.com and search member posts by member "helloagain". Hope this helps everyone out there.

                                                                                                                       Bo