Messages

1

General Mach Discussion / Re: Hi, Where can i get the wiring diagram to the board of a CNC 3040?

« on: May 01, 2014, 11:28:37 AM »

Hi,

Thanks....It Was okay for 2 weeks.... What kind of a better board can i look at on Ebay? Name? Sort? So i could get one that works 1-5 years... Not weeks...

Thanks!

Finland

2

General Mach Discussion / Re: Hi, Where can i get the wiring diagram to the board of a CNC 3040?

« on: April 19, 2014, 03:50:08 AM »

Hi,

Yes I Would want to make it all better but when I don't have the wiring diagram for all the boards ( Just the on you gave me)

Wich part is it that is broken if it is? so i could get a better on...

And The YOC PW 3024 I made it better

Thanks

3

General Mach Discussion / Re: Hi, Where can i get the wiring diagram to the board of a CNC 3040?

« on: April 19, 2014, 03:02:39 AM »

Hi,

Thanks for the help it helpt me! But now i have a Little problem...

Do you know what to do? The cnc3040 board is okay, and one day I was engraving and after 10 min when it was done so the spindle didn't stop, it keep runnig no difference if the spindle was on or off and the Emergency stop didn't work. So now when I put the Power on so the spindle is Always on and I can't change the speed on it.

What could be wrong?

Thanks!!

4

General Mach Discussion / Re: Hi, Where can i get the wiring diagram to the board of a CNC 3040?

« on: March 26, 2014, 07:33:52 AM »

Hi,

I put my file here. When I start the mach3 I put the wood on to the cnc and the blade to the wood surface and then zero all the X Y Z axises and then start.. But then it will drill strait in to the wood about 8MM

Thanks man!!

5

General Mach Discussion / Re: Hi, Where can i get the wiring diagram to the board of a CNC 3040?

« on: March 26, 2014, 07:08:28 AM »

Hi,

It works now but when I'm trying to do something with the cnc so it will drill straight down about 8mm, but i should only go about 3-4 mm..
But after the first 8mm then it will do the 3-4 mm as it should do.

Why so?

Is it the Board or some settings?

Thanks!!

6

General Mach Discussion / Re: Hi, Where can i get the wiring diagram to the board of a CNC 3040?

« on: March 25, 2014, 03:47:21 PM »

Hi,

The wiring diagram said that it is a 100 ohm resistor but it burnt right away...

Did I something wrong or was it the diagram for this board?

Thanks!

7

General Mach Discussion / Re: Hi, Where can i get the wiring diagram to the board of a CNC 3040?

« on: March 24, 2014, 09:03:58 AM »

Hi,

It didn't work.. I was spinning about 2min and 2000rpm and then it burns again.

thanx

8

General Mach Discussion / Re: Hi, Where can i get the wiring diagram to the board of a CNC 3040?

« on: March 23, 2014, 08:20:43 AM »

Thanks!

I will give it a try and let you know then!

Thanks!

9

General Mach Discussion / Re: Hi, Where can i get the wiring diagram to the board of a CNC 3040?

« on: March 23, 2014, 04:59:29 AM »

Hi,

It is a YOOCNC PW 3618 board and I but a mark on whats burn..

Thanks!

Finland

10

General Mach Discussion / Hi, Where can i get the wiring diagram to the board of a CNC 3040?

« on: March 22, 2014, 07:57:20 AM »

Hi,

I know this is the wrong place but I have to try...

Where can i get the wiring diagram to the board of a CNC 3040?

One compounent is dead...


Thanks!