Hello Guest it is June 10, 2023, 04:34:21 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - haensse

Pages: 1
General Mach Discussion / Re: Temperature Supervisor
« on: August 29, 2013, 12:15:12 AM »
Hi Hood

thinking about your code, it is the better solutions. It is the responsibility of the operator to restart the spindle.  Ugly scratches on the surface of the workpiece is better than a burned spindle....

I'll keep you updated about my test results

one hint for the hardware (is working fine as suggested in my earlier post). Use a 100Ohm resistor for wiring the analog output signal to the analog input (place it on the input connector). The controller and the temperature sensor have both a 0-10V range, but if for some reason the 24V supply (e.g. short) is feed to the analog input, the internal clamping diode in the controller will protect the controller. The 100Ohm will limit the current in the clamping diode.

General Mach Discussion / Re: Temperature Supervisor
« on: August 29, 2013, 12:00:10 AM »
Thank you Hood for the reply, but this would result in a ruined tool.

basically I would need the following info / steps (marked with ok, I should be able to code it)
check z axis to be >0
not moving (ok)
save M3 M4 M5 state (spindle was on? direction?)
send M5
prevent any further feeding / program cycle commands
wait temperature goes down again (ok)
restore M3/M4 state
wait 2 seconds (ok)
restart feeding

General Mach Discussion / Re: Temperature Supervisor
« on: August 28, 2013, 01:17:28 AM »
yes, but it only displays the temperature, don't know yet howto halt the active cycle and stop the spindle if the temperature is above a certain limit.

General Mach Discussion / Re: Temperature Supervisor
« on: August 27, 2013, 02:45:53 PM »
'10V = 4095 / 0V = 0
'10V = 160°C / 0V = 0°C

Finally placed this code into the macropump.m1s file. It polls the temperature from the CSMIO/IP-S analog input and displays it in the message box:

'Analog IN 1
adc = GetInput( 81 )
temp = round(adc * (160.0 / 4095.0))
If ( temp > 70 ) Then
   MESSAGE "Maschine braucht Pause T="&temp
   MESSAGE "Maschine ok T="&temp
End If


General Mach Discussion / Re: Temperature Supervisor
« on: August 18, 2013, 12:53:36 AM »
Temperature supervisor hardware is working now, I just bought the following components from Conrad Electronics and mounted it on the spindle enclosure. The module measures 0° to 160°C.

502155    Messumformer-Modul für PT1000 Hygrosens PT-MOD-10V-T2 0 - +160 °C    
172448    Einschraub-Platin-Temperatursensor Heraeus W-GJK (SCH) Heraeus-Nr. 30 010 000 -40 - +250 °C Messing mit Einschraubgewind    

General Mach Discussion / Temperature Supervisor
« on: July 23, 2013, 01:11:00 AM »

I'm using a modified BF20L from Mobasi with servo spindle that runs up to 6000rpm. The original machine just runs up to 3000rpm only. After two months now the bearing suddenly heated up to more than 130°C. Unfortunately I did not notice this immediately  :(. I opened up the spindle and found a lot swarf in the grease above the bearing. So it looks like those metal pieces found its way down into the bearing and ruined everything. Maybe it is also a problem to run the machine out of spec with doubled rpm  ???
However just to make sure next time that the machine will stop before major damage may arise, I would like to add a temperature supervisor that will
- move the z axis to defined z axis position.
- stop spindle
- wait until temperature is low again
- start spindle
- wait some time
- restart work

I would like to use a analog input on my ethernet controller.

Any hints how to implement this. Is a plugin needed?

best regards


General Mach Discussion / Panelize multiple parts
« on: June 28, 2013, 02:33:07 PM »

I created the g-code for a part. Now I would like to produce multiple parts without repositioning the origin and restarting the program. Is it possible to panelize the part, e.g. in a given grid with preset x and y offsets?

best regards


Pages: 1