Hello Guest it is March 18, 2024, 10:29:49 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Garfield

Pages: 1 2 3 »
1
General Mach Discussion / Re: How can i open a .mcc file and edit it?
« on: September 02, 2013, 04:43:38 AM »
Thanks,
i thought i could change the order of movement of the axis, because there is a bug in it.
Now i will ask the author of the Screen.

2
General Mach Discussion / How can i open a .mcc file and edit it?
« on: September 01, 2013, 11:51:27 AM »
Hello, what kind of tool do i need to open an .mcc and edit it?

Thanks
Garfield

3
General Mach Discussion / Re: Lower spindle speed needed
« on: May 30, 2013, 11:13:27 AM »
I have seen, it is no mach problem, but tripple beast, because there a 3 pins and 4 signals, so it switches relais, if pwm is over 10%
I can only let watchdog or current reduction unplugged, then there is a pin free for directly switch relais...the mechanical edgefinder runs on 600rpm and my spindle in this configuration starts at 1200rpm, is this a problem for the edgefinder?

4
General Mach Discussion / Lower spindle speed needed
« on: May 30, 2013, 02:57:01 AM »
Hello, i have the problem, my spindle starts at 1200 rpm, because the frequency converter needs a dc signal, i switched by a relay. The relay starts at a minimum speed at 1200 by mach 3. Is there a way to change the value, so my relay switched at 600 rpm, and not at 5% auf the max speed of 24000 rpm. I need lower speed for edgefinder...

5
General Mach Discussion / Re: unwanted creep in jog mode?
« on: February 14, 2013, 10:09:56 AM »
Hi, i have the same problem with shuttle pro Vers. 2.0. If i move the machine with the outer ring in one direction, and then release the ring, the machine does not stop, but walk very slowly in the direction i selected. It stops not untill i rotate it a little bit over zero in the other direction.
I use Mach3R3.043.058 german Version und the plugin available from this page.

6
General Mach Discussion / Re: New PlugIn just about done..
« on: February 14, 2013, 10:04:21 AM »
Hi, i use Mach3R3.043.058 german version

7
General Mach Discussion / Re: New PlugIn just about done..
« on: February 13, 2013, 06:54:19 PM »

Hello i have installed the shuttle pro 2.0 it is a nice plugin, thanks.
But if i move the machine with the outer ring in one direction, and then release the ring, the machine does not stop, but walk very slowly in the direction i selected. It stops not untill i rotate it a little bit over zero in the other direction?

Is this a bug? I think it should stop, when the ring is in Zero Position.

Ref all does not work. Only z-axis works when select the buttom with this setting
 

8
General Mach Discussion / Shuttle Pro Plugin some questions...
« on: February 12, 2013, 05:52:12 AM »
Hello i have installed the shuttle pro 2.0 it is nice.
But if i move the machine with the outer ring in one direction, and then release the ring, the machine does not stop, but walk very slowly in the direction i selected. It stops not untill i rotate i Little bit over zero in the other direction?

Is this a bug? I think it should stop, when the ring is in Zero Position.

Ref all does not work. Only z-axis works when select the buttom with this setting

9
General Mach Discussion / What's your settings on Shuttle Pro?
« on: February 12, 2013, 01:48:44 AM »
Hi,
i have bought a shutle pro, and thinking, how i should configure the buttom.
What for functions do you select with which buttoms?

Thanks
Garfield

10
General Mach Discussion / Re: Bugy Mach crashed my machine
« on: February 08, 2013, 11:41:07 AM »
Hi, the problem with the spindle is solved. In the config of ESS PWM was not checked. I have klicked on it, but have forgotten to restart mach3
With the homing-problem, the older Versionof english mach 3 works...

Pages: 1 2 3 »