Messages

1

CS-Lab / Re: First impressions of CSMIO/IP-A (analogue output version)

« on: August 11, 2013, 03:33:10 PM »

Hood,
Iam sorry but I think I sent the wrong one.
See this one looks better?

Thanks,
Apollo ll

2

CS-Lab / Re: First impressions of CSMIO/IP-A (analogue output version)

« on: August 10, 2013, 10:44:05 PM »

Hood,
The machine I have is a Bridgeport Apollo ll. It is a 3 axis cnc knee mill. 1993 vintage.

Thanks,
Apollo ll

3

CS-Lab / Re: First impressions of CSMIO/IP-A (analogue output version)

« on: August 10, 2013, 10:41:44 PM »

Hello Hood,
Trying again.

Thanks

4

CS-Lab / Re: First impressions of CSMIO/IP-A (analogue output version)

« on: August 10, 2013, 04:38:41 PM »

I will try once more.

Apollo ll

5

CS-Lab / Re: First impressions of CSMIO/IP-A (analogue output version)

« on: August 10, 2013, 04:27:24 PM »

Hello Hood,
I can not send the xml file. It says I already submitted that post. Any ideas how to send it?

Thanks,
Apollo ll

6

CS-Lab / Re: First impressions of CSMIO/IP-A (analogue output version)

« on: August 10, 2013, 02:05:25 AM »

Howdy Hood, I have several issues that I could use your advise on.
1) On a CS-MIO--IP-A to an Apollo II hook up what is the wire to pin configuration when connecting the analog X, Y and Z (+/-10v) to the Axis Drive Boards? I am not getting ten volts from the outputs to control the Axis Drive Boards. Am I supposed to supply voltage some how or is the CS-MIO supposed to supply it?
2) What do I hook up the spindle break to?
3)I have my eject tool function hooked to output 1. How do I tell the Mach III program what that port is so it can control it, and the same with all the outputs?
Thanks a ton.
Apollo ll

7

CS-Lab / Re: First impressions of CSMIO/IP-A (analogue output version)

« on: May 06, 2013, 01:56:26 AM »

Hey Hood, Sorry to bombard you with all these questions but I sure do appreciate the help. It will be great to see this in action once it is done. Along with the Proximity switch I am trying to tie in the last of the spindle control. The spindle speed control signal says it takes a 0 to +/- 12v analog but the CSMIO only has +/- 10v analog. Does that hook to the analog +/- 10v or the analog 0-10v output. And will it affect the actual speed since it is 10v instead of the 12v that it was originally.
Apollo ll

8

CS-Lab / Re: First impressions of CSMIO/IP-A (analogue output version)

« on: May 05, 2013, 12:27:20 PM »

Hello Hood,
Here is a link for the part.

http://datasheets.globalspec.com/ds/52/EuchnerUSA/95C10632-D76F-44BC-98F7-5BD973F69129

9

CS-Lab / Re: First impressions of CSMIO/IP-A (analogue output version)

« on: May 04, 2013, 03:00:01 PM »

The web site I found it on is, www.datasheets.globalspec.com
Part # EGT 12x02AP024-SEM4

Apollo ll

10

CS-Lab / Re: First impressions of CSMIO/IP-A (analogue output version)

« on: May 04, 2013, 12:57:26 PM »

Hello Hood,
As far as the axis motion, and the jog switch Im going to order the MPG Module and pendant from CS Labs.
You were right it is a proximity switch. Part number EGT12x02AP024-SEM4. It looks like it will handle 30volts, and 250ma. Im not sure how to hook it into the CSMIO though?
Any ideas?
Thanks for all your help!

Apollo ll