Hello Guest it is January 20, 2021, 08:54:25 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Anthony

Pages: 1 2 3 »
1
General Mach Discussion / 4th axis Teach
« on: May 08, 2008, 04:47:19 AM »
Hi,
  Can Mach3 Software be used to teach the 4th axis (wizard "Teach") ? Thank you.

            Anthony

2
General Mach Discussion / Re: External buttons
« on: April 27, 2008, 05:54:07 AM »
Hi Hood,
 thank you for your help, i will wait your next good news.

best regards

Anthony

3
General Mach Discussion / External buttons
« on: April 27, 2008, 03:34:43 AM »
Hi,
 Who can explain me how to find a pin for connecting an external button "cycle start" and an external button "go to Z" ?
Thank you.

regards


Anthony

4
General Mach Discussion / Re: Milling machine
« on: April 04, 2008, 04:43:21 PM »
Hi! Jimpinder Here is the translation of my sheet, can you find a solution for my milling machine ?
1,2,3 Erdung: Earth potential
4,5,6 Nulleitung: Zero potential (in Germany Earth and zero potential are separated)
7: Strom : means the 220V power supply?
8: Fräse Strom: 220V power supply mill machine
9: Steckdose: 220V power supply power socket
10,11: Rele..?: Relay connectors
12: +12V: +12V supply
13: +5V supply
14: ?? Mase??: perhaps GND for +12V,+5V, for controller supply
15,16: +24V for motor supply
thanks

5
German / Re: Übersetzung
« on: April 04, 2008, 02:32:29 PM »
Hi! Wolfram,

Thank you very much for your help.

regartds

Anthony

6
German / Übersetzung
« on: April 01, 2008, 02:40:29 PM »
Hallo,
Wer kann mir in Englisch übersetzen dieses Blatt bitte?

gruss

Anthony

7
General Mach Discussion / Re: Milling machine
« on: March 31, 2008, 03:19:49 PM »
Hi! I have a sheet written in German that matches pins, but . I know that pin 8 match electricity of my spindle.I tried it but it didn't work. I am saying that I don't know the numbers of the pins that are controlling my spindle.
I am using my keyboard to control the axis motors on my system with Mach3 Software,thanks.


regards


Anthony


8
General Mach Discussion / Re: Milling machine
« on: March 30, 2008, 05:07:07 AM »
Thank you very much. I tried it.



  Regards,                                                                   Anthony

9
General Mach Discussion / Re: Milling machine
« on: March 29, 2008, 03:13:59 AM »
Thank you for your information, I tried it but my milling machine don't run. I don't know how to configure the spindle. I don't know the pins of my spindle.



   Regards,                                                                                         Anthony

10
General Mach Discussion / Re: Milling machine
« on: March 28, 2008, 02:59:30 PM »
I am not asking how I start a program. I have a machine, it is set up, I use Mach3 software. My milling machine is wired into my controller card. I want to switch on and off my milling machine with a GCode command (a line of a program GCode) in a program GCode. Can you tell me how to activate and configure my milling machine in Mach3 software ?
Thank you.


     Anthony

Pages: 1 2 3 »