Messages

1

Building or Buying a Wood routing table.. Beginnners guide.. / Re: chinese spindle wiring

« on: November 26, 2013, 06:08:25 PM »

the settings is my big problem on the inverter

2

Building or Buying a Wood routing table.. Beginnners guide.. / Re: chinese spindle wiring

« on: November 26, 2013, 06:07:00 PM »

HI CAN YOU PLEACE HELP ME WITH THIS SETTINGS ON MY NEW SPINDEL. I CANT GET IT TO WORK AT ALL.
1.   SPINDEL
2.   3KW
3.   FREQUENCY 100
4.   SPEED 2400RPM
5.   VOLTAGE OF MOTOR 220VAC
6.   FULING ELECTRIC
7.   DZB312B003.7L2DK     NO. 4012216DK13381071 SERIES INVERTER
8.   INPUT VOLTAGE TO INVERTER IS 220VAC
9.   WERE DO I CONECT THE 220V (R,S,T)  SPINDEL (U,V,W)
10.   SPINDEL (1EARTH,2,3,4)
11.   THERE IS ALL THE F1,F2,F3 SETTINGS
12.   I NEED MACH3 (TO SWITCH THE SPINDEL ON AND OFF)

3

General Mach Discussion / Re: computer keep on switching of when the plasma ark(spark)

« on: November 26, 2013, 10:42:05 AM »

THANKS NICK. THE PROBLEM IS THAT MY INVERTER MODEL IS A DZB312 AND ALL THE INFO I CAN GET
(USER MANUAL) IS FOR A DZB300.

4

General Mach Discussion / HELP ON SPINDEL SETUP

« on: November 25, 2013, 01:30:21 PM »

HI CAN YOU PLEACE HELP ME WITH THIS SETTINGS ON MY NEW SPINDEL. I CANT GET IT TO WORK AT ALL.
1.   SPINDEL
2.   3KW
3.   FREQUENCY 100
4.   SPEED 2400RPM
5.   VOLTAGE OF MOTOR 220VAC
6.   FULING ELECTRIC
7.   DZB312B003.7L2DK     NO. 4012216DK13381071 SERIES INVERTER
8.   INPUT VOLTAGE TO INVERTER IS 220VAC
9.   WERE DO I CONECT THE 220V (R,S,T)  SPINDEL (U,V,W)
10.   SPINDEL (1EARTH,2,3,4)
11.   THERE IS ALL THE F1,F2,F3 SETTINGS
12.   I NEED MACH3 (TO SWITCH THE SPINDEL ON AND OFF)

5

General Mach Discussion / Re: computer keep on switching of when the plasma ark(spark)

« on: November 25, 2013, 01:12:52 PM »

HI CAN YOU PLEACE HELP ME WITH THIS SETTINGS ON MY NEW SPINDEL. I CANT GET IT TO WORK AT ALL.
1.   SPINDEL
2.   3KW
3.   FREQUENCY 100
4.   SPEED 2400RPM
5.   VOLTAGE OF MOTOR 220VAC
6.   FULING ELECTRIC
7.   DZB312B003.7L2DK     NO. 4012216DK13381071 SERIES INVERTER
8.   INPUT VOLTAGE TO INVERTER IS 220VAC
9.   WERE DO I CONECT THE 220V (R,S,T)  SPINDEL (U,V,W)
10.   SPINDEL (1EARTH,2,3,4)
11.   THERE IS ALL THE F1,F2,F3 SETTINGS
12.   I NEED MACH3 (TO SWITCH THE SPINDEL ON AND OFF)

6

Post Processors / Re: Here's Delcam Featurecam Mach3 Mill and Turn Post Processors

« on: September 03, 2013, 11:11:43 PM »

Hi Mitch,

Assuming you are using the Parallel Port then it may just be worth checking the voltage between an LPT axis Direction Signal pin and GND (pin 25) whilst jogging that axis in each direction.
The newer Parallel Ports use 3.3 Volt TTL logic and many of the cheap Chinese controllers like to see the older 5 Volt TTL logic signals.

Tweakie.

Thanks for your help.  I have found the problem.  Just about to dump the usb mpg (Chinese)( xhc  hb04) and I open it up to find that there were dry solder joint on the pc board. Re-solder it and it works perfect. All the buttons work like they were meant to. I hope this is to some help to people that have got some eBay stuff from “goodluck.com”
Cheers from sunny South Africa
Mitch Mitchell

7

Post Processors / Re: Here's Delcam Featurecam Mach3 Mill and Turn Post Processors

« on: September 03, 2013, 04:39:14 AM »

Hi form Cape town South Africa
My milling machine latest mach3(full) . Go on ebay mpg (Chinese)( xhc  hb04) only want to move
In +direction and not in the –direction. Have installed the program. Sorry my English not to good
Cheers Mitch

8

General Mach Discussion / Re: computer keep on switching of when the plasma ark(spark)

« on: May 27, 2012, 03:29:49 AM »

Thanks Tweakie
Will have a look monday.
CHEERS
MITCH

9

General Mach Discussion / computer keep on switching of when the plasma ark(spark)

« on: May 26, 2012, 05:13:44 PM »

PLS HELP ME IN SOUTH AFRICA
I have a plasma cnc from CNC-DIRECT with THC controller (leeuwinga). Just bought a new computer for the cnc (old one ran out of memory). My plasma is from tradeweld CUT 40H. I fit a filter on the plasma 220v input. The plasma cut very well in one go but as soon as there is a second cut in the same ***.dxf or ***.tab then the computer switch off completely.
Thanks
Mitch Mitchell