Hello Guest it is March 29, 2024, 10:10:52 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - wickytje

Pages: 1
1
Galil / Re: GalilInit
« on: March 19, 2012, 11:13:47 AM »
I have read that you are one of authors of galilplugin and  understand that there  are many problems to take care about , hope you can isolate and solve this  problem .
 Until then I will try                - earlier plugins
                                           - geared axis  squaring done in galil  ( we will use mpg to test )
can you tell where to find earlier plugins  and there user pdf
Firuz

2
Galil / Re: GalilInit
« on: March 16, 2012, 03:44:39 AM »
Tuning parameter in mach                              master=slave
Servos and encoder type                                 master=slave
%sp homing                                                  master=slave
Motor tuning parameter in galil                        master=slave
Home slave with master axis                           uncheck
Perform axis squaring                                     check

3
Galil / Re: GalilInit
« on: March 15, 2012, 06:09:32 PM »
Hi Kenny
I agree will spare me lots of time but  had problem of double speed of slave axis when homing in mach . Is there any solution for  this problem at this moment
 btw I have very little experience with cnc  i am building may first mill witch is supposed to be finished in two months ,,,,,  if I can find solutions for gentry  and some more  
Firuz

4
Galil / Re: GalilInit
« on: March 14, 2012, 10:17:50 AM »
Hi Kenny
Many thanks for replays .I read prog pref and manual 18xx6  made a small program labeled it #AUTO and  BP to controller . it seems to work perfectly after reset and power up .
Want to try to make homing routine for gentry in plugins ,replacing master axsis homing command in Edit button script with NotifyPlugins(3000)     3000=example  will it work , any suggestions
Firuz

5
Galil / Re: GalilInit
« on: March 13, 2012, 01:25:22 PM »
The controllers I have are 1876  and 1880 with 2xAMP1940  so I can experiment with extra axis .I used Z,Y, GA,,CY as an example for axis and commands .
 Can you tell more about , ore what do I do wrong not getting any commands to controller when using  GalilInit.txt

6
Galil / Re: GalilInit
« on: March 13, 2012, 01:15:26 PM »
The controllers I have are 1876  and 1880 with 2xAMP1940  so I can experiment with extra axis .I used Z,Y, GA,,CY as an example for axis and commands .
 Can you tell more about , ore what do I do wrong not getting any commands to controller when using  Galilainit.txt

7
Galil / Re: GalilInit
« on: March 13, 2012, 11:29:53 AM »
Hi Kenny
Plan is to keep slaved axis invisible for mach (slave axis will not be configured in mach )
Firuz

8
Galil / GalilInit
« on: March 13, 2012, 05:31:21 AM »
Hi
I am working on a three axis mill  , am trying  mach3 galil DMC1876 combination .  Spindle I could manage on W axis for 0 10v (had to do some programming on M2 and M3 to stay in CW) output 1 stop start /output2 CW CCW . Now I am experimenting with  slaving Z to Y I have made with notepad  a text file called GalilInit.txt  with GA,,CY  than saved it in to plugin folder restarted mach3 when looking into galil debug file I can’t find any GA,,CY
Can anyone help?
Firuz

Pages: 1