Messages

1

General Mach Discussion / Re: bobcad posts and taig ops

« on: October 03, 2011, 08:43:08 AM »

XML??

This is a simple file but responds the same...

(BEGIN PREDATOR NC HEADER)
(MCH_FILE=4AXVMILL.MCH)
(MTOOL T1 S1 D.125 H.5 A0. C0. DIAM_OFFSET 1 = .0625)
(SBOX X0. Y0. Z-.0625 L4.5 W2.75 H.0625)
(END PREDATOR NC HEADER)

%
O100
(PROGRAM NUMBER)
(PROGRAM NAME - DUPLEX.TAP)
(POST -  MACH 3 MILL NO ATC)
(DATE - SUN. 10/02/2011)
(TIME - 05:01PM)

N01 G20 G40 G49 G54 G80 G90 G91.1
;N02 G53 Z0.


;N03 T1 M6
N04 S5011 M03
N05 G00 G90 G54 X.9875 Y1.0568
;N06 G43 H1 Z.25
N07 G01 Z-.08 F20.0459
N08 G17 G03 X1.9825 Y.9994 I.5175 J.3182 F39.0895
N09 G01 Y1.7506
N10 G03 X.9875 Y1.6932 I-.4775 J-.3756
N11 G01 Y1.0568
N12 G00 Z.25

(BEGIN PREDATOR NC HEADER)
(MCH_FILE=4AXVMILL.MCH)
(MTOOL T1 S1 D.125 H.5 A0. C0. DIAM_OFFSET 1 = .0625)
(SBOX X0. Y0. Z-.0625 L4.5 W2.75 H.0625)
(END PREDATOR NC HEADER)

%
O100
(PROGRAM NUMBER)
(PROGRAM NAME - DUPLEX.TAP)
(POST -  MACH 3 MILL NO ATC)
(DATE - SUN. 10/02/2011)
(TIME - 05:01PM)

N01 G20 G40 G49 G54 G80 G90 G91.1
;N02 G53 Z0.


;N03 T1 M6
N04 S5011 M03
N05 G00 G90 G54 X.9875 Y1.0568
;N06 G43 H1 Z.25
N07 G01 Z-.08 F20.0459
N08 G17 G03 X1.9825 Y.9994 I.5175 J.3182 F39.0895
N09 G01 Y1.7506
N10 G03 X.9875 Y1.6932 I-.4775 J-.3756
N11 G01 Y1.0568
N12 G00 Z.25


N13 S5011
N14 X3.5125 Y1.7506
N15 G01 Z-.08 F20.0459
N16 G03 X2.5175 Y1.6932 I-.4775 J-.3756 F39.0895
N17 G01 Y1.0568
N18 G03 X3.5125 Y.9994 I.5175 J.3182
N19 G01 Y1.7506
N20 G00 Z.25
N21 M05
;N22 G53 Z0.
;N23 G53 Y0.

(END OF PROGRAM)

N24 M30
%

(END OF PROGRAM)

N24 M30
%

2

General Mach Discussion / bobcad posts and taig ops

« on: October 02, 2011, 10:58:44 PM »

CNC is new to me am attempting to learn and use.
Have Bobcad V24, have tried several posts all start with Mach3.
Running a Taig DLS 3k.
Can jog (DRO) and examples all control to correct size ie 1"= 1"
create a part in Bobcad post it and it is off by almost a factor of 10   0.1"=1" +/-
and after loading & closing file - jogging with DRO is now off by same factor
G codes seem fine.

Where should I start looking???

3

Mach4 General Discussion / Re: New people welcome !! Come in here and introduce your self!

« on: October 02, 2011, 10:56:26 PM »

CNC is new to me am attempting to learn and use.
Hobbyist at this point but really want to get some stuff built.
Will be tapping your experience from time to time.