Hello Guest it is January 29, 2023, 01:07:13 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - edcross

Pages: 1 2 3 4 »
1
Mach4 General Discussion / Re: m6 macro
« on: September 28, 2022, 08:37:05 AM »
 Thanks   .  Ed

2
Mach4 General Discussion / m6 macro
« on: September 22, 2022, 08:39:52 AM »
 Attached  m6 macro works in Mach 4 V4612  ,  but does not work in V4809 , any ideas .

   Thanks

     Ed

3
Mach4 General Discussion / Mach4 v 4809 script editor error message
« on: July 16, 2022, 02:00:57 PM »
C:\Mach4Hobby\Profiles\ESS G540 VFD\Macros\m6.mcc: Binary file is shown as read-only as it is only partially loaded.
C:\Mach4Hobby\Profiles\ESS G540 VFD\Macros\mcLua.mcc: Binary file is shown as read-only as it is only partially loaded.
 
 When i load mach 4 and open the script editor , the above message is in the box under the script , does any one know why ??. 

    Thanks

       Ed

4
Mach4 General Discussion / m6 macro
« on: July 15, 2022, 11:14:32 AM »
The error attachment is the error on the m6.mcs bottom window box , after i load mach4 4809 ? . The 2 nd attachment is the m6 macro i copied from a mach 4 video on youtube. When i run a m6 command from MDI window , , it goes to the correct position in the script , but when i hit the OK to probe , it says it is probing but no movement from the Z axis and the diagnostic window on Mach 4  does not show the probe active . Is there something missing from the script ?  .  Mach 4 --Smoothstepper ESS -- Gecko 540  .

      Thanks

        Ed

5
General Mach Discussion / Re: Circle not round
« on: June 01, 2022, 08:43:21 AM »
 Got the answer on Warp9 site.

     Ed

6
General Mach Discussion / Circle not round
« on: May 30, 2022, 01:19:32 PM »
Mach 4 v4612 - Aspire 11.14 - gecko 540 - smooth stepper . When i create a 12" circle in Aspire , save with Mach 2/3 atc arc pp from vectric , the circle cuts 12" in Y and 12 1/4" in X , any suggestions . Calibrated all axis in Mach 4 wizard ( does not matter if i ( cut outside - on line - inside ) always around 1/4 " off !

     Thanks

       Ed

7
Mach4 General Discussion / Re: mach4 and wrap gcode
« on: May 05, 2022, 11:27:46 AM »
  This is a rotary project , Y is not used . This file cuts fine , it just does not show up correctly on the Mach 4 screen.

     Ed

8
Mach4 General Discussion / Re: mach4 and wrap gcode
« on: May 04, 2022, 01:49:27 PM »
 I guess Mach support doesn't look at the forum any more .

    Thanks

      Ed :-[

9
Mach4 General Discussion / mach4 and wrap gcode
« on: April 30, 2022, 12:19:59 PM »
 When i load this attached and any wrapping gcode file , Mach 4 latest, just shows' a line on the display ( 4w screen set ) and not the part ??.

    Ed

10
Mach4 General Discussion / Re: Change screen set
« on: April 07, 2022, 02:26:13 PM »
 Amen !

    Ed

Pages: 1 2 3 4 »