Messages

1

General Mach Discussion / Re: G91 and others problems

« on: May 19, 2011, 11:11:34 AM »

I also always used the G90, but my client has a CAM called LANTEK that generates everything G91. It's hard to change his idea to work on G90. Programs incremetal, I think is very dangerous.
Thanks for your reply.

2

dspMC/IP Motion Controller / MPG - Hardware - Softlimit

« on: May 18, 2011, 04:20:14 PM »

 With DSPMC the problem is:
 MPG mode, Software Limits do not work, leaving the axes collide mechanically. Only in this situation.

 If someone can help me ..Thanks

3

General Mach Discussion / Re: G91 and others problems

« on: May 18, 2011, 04:11:35 PM »

So we have nothing to do .... But in the MACH2 think it worked.
 Thanks
 

4

General Mach Discussion / G91 and others problems

« on: May 17, 2011, 02:06:10 PM »

Tradução do português para inglês

G91 and other problems.

 Please I need help on some issues.

 I am using the latest versions of MACH3 XX.43.22 and some earlier and noticed the following.
 1. When we work on the G91 there is information that is not possible to stop and return the program REVERSE MODE.OK? Is it possible that someone's day?

 2. When in G91 and STOP program for cleaning up a torch or something and made ​​a command "RUN FRON HERE", the axes will move exactly twice the requested coordinates on the line where we start running. Seems to me that the versions of MACH2 did not.
 Is that correct?
 3. What can I do to my FEED HOLD or PAUSE is faster, ie, immediately stop the axes. I have a long delay until the axle stop.
 Attached the gcode I'm working on my Oxycorte.
 The deceleration of the axes are between 0.5 sec per axis.

 Such cases occur with either the SS or PP.

 With DSPMC the problem is:
 MPG mode, Software Limits do not work, leaving the axes collide mechanically. Only in this situation.

 If someone can help me ..Thanks

5

Finished Screens / Re: Ultimate Screen Mill/Lathe/Plasma (TouchScreen and/or Mouse and/or keyboard)

« on: May 04, 2009, 10:28:14 AM »

Zealous,

My Mach3 is 3.042.21.

You received my  contact, in your e-mail? 
Please, send this for machmotion.

Thanks

6

Finished Screens / Re: Ultimate Screen Mill/Lathe/Plasma (TouchScreen and/or Mouse and/or keyboard)

« on: April 27, 2009, 03:45:04 PM »

Zealous,

I sent email to tech@machmotion.com with what I sent to you earlier, but had no response from them.
I think really that I lost my money.
It is very bad to know that ...
The Screen has many errors and we do not have any support them.
To make the payment they promptly responded to e-mail, but now I do not have any answers.

I am disappointed.

7

Finished Screens / Re: Ultimate Screen Mill/Lathe/Plasma (TouchScreen and/or Mouse and/or keyboard)

« on: April 24, 2009, 11:52:22 AM »

Zealous,

The problem is not setup Mach3.
I did more than 15 machines with Mach3.
The problem is more complex.
For example the button "Online" does not work when activated, but when the Mach3 config menu, under "Operator" I drive "offline Control", the LED of the button on-line changes state.
I am attaching it with the previous message and sending to Tech@machmotion.com, I hope to answer them this time.

Regards,

Prendice

8

Finished Screens / Re: Ultimate Screen Mill/Lathe/Plasma (TouchScreen and/or Mouse and/or keyboard)

« on: April 24, 2009, 12:23:26 AM »

Zealous,

I think that has something wrong.
My version is 1.0.2.B, I received less than 2 weeks.
It does not work many functions ..
In the video has a button "Tooling" on my screen is Offset "..
Below some functions that do not work.

Screen Limits:
Soft limits
Z Inhibit off
Machine
To Go
Online

Screen Controls:
Single Block
M1

Scripting
Brains

Tool Path:
Mcodes

Manual overide off limits
Jog Mode
Jog on

In Simulate mode, it acts as Run and do not show the Estimate Time.

Rotate
Pan
Zoon, such functions do not work

Tool Offset Information:
Auto Zero
Remember
Ignore tool change on

Finally, there are several functions that in my Machotion not work, maybe issue a release or installation.

I await your response.

9

Finished Screens / Re: Ultimate Screen Mill/Lathe/Plasma (TouchScreen and/or Mouse and/or keyboard)

« on: April 23, 2009, 09:18:33 PM »

Thanks, Zealous

But what about the Single Block button? He really does not work.

It will be great to have led to indications of SB.
 
How can I make a button with the " Script Button", for example, a button of "Auto Tool Zero" or other ...
 
Ok I understand that this is TSpindel, but on my screen it only works in the range of rotation, ie when I turn or change the rotation, but after that it back off of the state .. I need an encoder in Spindel ....... to measure the rotation real?
 
Where can I get a longer version with these changes?

I need another "keycode"?

Thank You.

Regards,

Prendice

10

Finished Screens / Re: Ultimate Screen Mill/Lathe/Plasma (TouchScreen and/or Mouse and/or keyboard)

« on: April 23, 2009, 07:51:21 PM »

Hello, Zealous

I bought the MACHMOTION screen, after installing and testing, I found some flaws and I have some doubts.
I sent email to Joel (MachMotion), and he did not reply! I lost U $ 199.00?
You could help me?
Below my doubts.
 
1. Single Block - button, only appears on a screen and do not work when
accessed.
There is no Led in the other pages to indicate that this mode is selected.

2. The execution time of program is always reset when stop is triggered, thus
lose the basis of previous time, it would be better just stop time and do not
delete it.

3. What is TSpindel? He acts not only when triggered Spov + or-Spov, he should
show the current rotation?

4.How I do to access the AMPS and K and L and P?
They are a random number of 238 in all.
What OEM / Dro needed to measure the Spindel AMP?

Thank You.......