Hello Guest it is November 30, 2022, 09:34:48 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Largemouthlou

Pages: 1 2 »
1
General Mach Discussion / Re: Need a little help on steps per min
« on: July 30, 2011, 03:20:04 PM »
I was looking for that earlier on the screen I'm using and it wasn't there, I didn't think of trying one of the other profiles.. I will get back down there early tomorrow and mess with that for awhile.. Thanks

2
General Mach Discussion / Re: Need a little help on steps per min
« on: July 30, 2011, 01:28:44 PM »
Yes, they have the same gear reductiuon same amount of teeth and Ron gave them the same values on his instruction sheet. There has to be something I missed somewhere but not sure.

Thanks for looking Hood :D

3
General Mach Discussion / Need a little help on steps per min
« on: July 30, 2011, 12:36:46 PM »
Finally back at my 4 X 8 precision Plasma build, been off of it due to heavy work load.

If I try to cut a 5" X 5" square the  Y is 5" but the X is 4 inches. I have all the steps per min the same on the X, Y, and A axis so I can't figure out what is wrong. I verifid the G code as having 5" move ment on all 4 sides.

I'm attaching the XML code (I hope) Thanks Hood for getting me straight on the XML

Thanks for any help

4
General Mach Discussion / Re: cant get dxf files to open
« on: January 22, 2011, 05:08:11 PM »
Sounds like ya got it covered!!! Can't wait till I can get my ideas out and rolling :)

5
General Mach Discussion / Re: cant get dxf files to open
« on: January 22, 2011, 10:50:24 AM »
Put your dxf files on a flash drive so you can view them in the puter with the cad program..

6
General Mach Discussion / Re: Mach XML Reader
« on: January 22, 2011, 08:39:03 AM »
I'm sure it is just my luck with computerd items but had trouble with the down load..

unzipped file, double clicked on XML reader exe file and got this application error message

application error
exception e read error in module mach_xml_reader.exe at 00025927
error reading JV tipsof the day1.show hints on setup: failed to set data for '_jvtipsof the day1:

OS is Vista..

7
General Mach Discussion / Re: Any Mach3 Experts in South Florida?
« on: January 20, 2011, 05:43:42 AM »
John, I keep ice cold beer at the shop ;D ;D

Do any bass fishing??

8
General Mach Discussion / Re: Enlargement problem
« on: January 20, 2011, 05:37:57 AM »
Come on Lou - nobody admits defeat this quickly.

Get your 'steps per' correct then everything else will fall into place (not sure about your THC though).

Tweakie.

LOL,,, I know, but I have been working on and off for the last 6 months, it gets a little frustrating when ya spend many a weekend on a project and don't get any where..LOL

Thanks, I will keep plugging away one problem at a time, finally got internet at the shop this will help as well : )

Good words to live by Tweakie  "Success consists of going from failure to failure without loss of enthusiasm.  Winston Churchill."

9
General Mach Discussion / Re: Enlargement problem
« on: January 19, 2011, 05:38:30 AM »
Haven't gotten back to this yet, worked on the DTHC card for my HYper1250.. I have checked and redid the wireing on that card 5 times, did all the test, rewiered, re splices and scratched my head till it is raw all to no avail..

Was told by Tom C that if the card passes all the tests then it is in the wireing...... So I checked it 3 more times and no tourch on?????????????????????????????????

Should have bought a turn key unit :-\

10
General Mach Discussion / Re: Any Mach3 Experts in South Florida?
« on: January 18, 2011, 08:39:58 PM »
Hey Brent, Im just below West Palm Bch in Lantana, did you ever get the help ya need??

Pages: 1 2 »