Messages

1

Finished Plugins for Download / Re: Huanyang VFD controller plugin

« on: May 02, 2013, 08:04:52 AM »

Hello Everyone,
I am currently using a Galil controller. I have a few issue using the plug in. The home switch are being ignored when plug in is activated, but if i remove the huanyang plug in the home switches works perfect. Does anyone have the same problem. Thanks in advance

2

Galil / Re: Galil DMC 21XX

« on: July 03, 2012, 06:35:35 PM »

Hello Steve,

Thank you very much for your reply and Information regarding the Gantry problem on Galil DMC21XX. I have solve the problem by using each individual home inputs rather limits using them as home inputs. Thank you very much again.

Cheers
Renato

3

Galil / Galil DMC 21XX

« on: June 23, 2012, 10:03:39 PM »

Hello Everyone,

I am currently having problems with my Home routine and slave axis using Galil DMC 21xx.
IF I use galil plugin version 4.4 the home sequence works fine, But i cannot get Axis to slave on the X Axis.
If t use Galil Plugin Version 4.5 which is I think the right plugin for this controller the slave axis works but home routine doesnt.
I hits the limit switch and stop and does nothing.
Anyone has the same problem? I would appreciate very much if you could help me with this problem. It might just be a mistake on my setup. Thank you .

4

General Mach Discussion / Re: JNC-40M configuration?

« on: June 21, 2012, 11:08:53 PM »

Hi to All
I got a JCUT 5060 and was able to setup the machine properly. Except when you jog X and Y axis using the keyboard shortcut keys the motor stalls. I have check the mechanics and seems to be OK. Did you have the same problem?

5

General Mach Discussion / Re: Properly doing "Run Frome Here"

« on: July 12, 2010, 02:08:05 AM »

Hello Hood,

That might be the case.  Anyway thank you very much for your support

Thanks
Renato

6

General Mach Discussion / Re: Properly doing "Run Frome Here"

« on: July 11, 2010, 11:03:03 PM »

Hi Peter, Hood.

Sorry for the late reply. We were busy the whole week moving to a new Factory. Anyway I have tried SNL which Hood and you suggested. I have notice that the feedrate is not taken into account when running SNL.

Thanks
Renato

7

General Mach Discussion / Re: Properly doing "Run Frome Here"

« on: July 03, 2010, 08:06:45 PM »

Hello Peter

Thanks for spending time running a test on the current problem that I am having.

Thanks
Renato

8

General Mach Discussion / Re: Properly doing "Run Frome Here"

« on: June 30, 2010, 06:32:47 PM »

Hello Peter,

Thank you for your ideas, time and Help. I will investigate more and will let you know the outcome.

Thanks

Renato

9

General Mach Discussion / Re: Properly doing "Run Frome Here"

« on: June 30, 2010, 08:04:01 AM »

Hi peter

Any RFH starting M71. Point taken on G53 thanks for the correction.

Thanks
Renato

10

General Mach Discussion / Re: Properly doing "Run Frome Here"

« on: June 30, 2010, 07:34:45 AM »

Hello Peter


I have attached a sample Gcode below. The code has been working for a long time on our 20 year Old CNC controller. Sorry about the mess. Once I get the right format that will work on Mach 3. The code will be cleaned up with labels and line numbers.


N9992
G90
G71
G0
M70
G53
X629.14Y297.00
M71
F5000
G1X352.50
G0
M70
X350.64Y296.00
M71
G1X319.64
G0
M70
X317.63Y297.00
M71
G1X41.12
G0
M70
X39.64Y296.00
M71
G1X9.14
G0
M70

Thanks
Renato