Messages

1

General Mach Discussion / Re: Conversion of Denford TRIAC milling to LPT

« on: July 16, 2012, 06:54:05 AM »

Thanks Jim for everything.
Please send me the wires drawings you made,to make it easier for me.
My email: usamahandal@hotmail.com

Thank you again.
Usama

2

General Mach Discussion / Re: Conversion of Denford TRIAC milling to LPT

« on: July 15, 2012, 01:48:22 PM »

Thanks for your time. So, if you are sure that it will have losing steps, I don't need to try it then.
My machine is 1987, and I have the electrical drawings for it, but I need the motor specifications like motor amp and also I want to know if the Z motor like the X and Y motors in amp (amper)?

3

General Mach Discussion / Re: Conversion of Denford TRIAC milling to LPT

« on: July 15, 2012, 09:22:49 AM »

Thank you Jim.
I think that changing the controller will be my last chance.
If I can make it with break board only it is better for me. As what (angel tech) did.

Usama

4

G-Code, CAD, and CAM discussions / Re: CorelDraw PLT to Gcode

« on: July 15, 2012, 08:55:39 AM »

I use CorelDraw with Rojer screenset , it is perfect for Corel.

http://www.machsupport.com/forum/index.php/topic,5182.0.html

Usama

5

General Mach Discussion / Conversion of Denford TRIAC milling to LPT

« on: July 15, 2012, 07:22:43 AM »

Hello everybody, I bought an old non-used TRIAC milling machine (the green one), and I want to convert it to work with MACH3.
I read almost all of the Posts that talk about this, but I didn't find any clarifications or descriptions on how to convert it.
I have in the attached file the Pin Configurations for the input cable to the controller of this machine.
I want your help in connecting this cable with the breakout board in order to work on MACH3.
Thanks in advance.

Usama

6

G-Code, CAD, and CAM discussions / Re: Total lines in the G Code for each file ??

« on: March 01, 2012, 08:50:43 AM »

Thank you Ya-Nvr-No ,
This is exactly what I need. Now I can open long files in the same time with a total line number which I will use it to give me a percentage of the finished work.
Thank you again, and I want to thank all the members for their help.

UH

7

G-Code, CAD, and CAM discussions / Re: Total lines in the G Code for each file ??

« on: March 01, 2012, 04:39:03 AM »

BR549, I only have one more question.

All my files are more than 300.000 lines, so when I put your code, it took about 2 minutes and 30 seconds to load the file, while when I open it without the code it takes only 11 seconds.
So what I mean is, is there any way that we can know the total lines for the file without counting them one by one as the code did, so it can take less time ??

And of course thank you for your help, and I appreciate it.


Regards,
UH

8

G-Code, CAD, and CAM discussions / Re: Total lines in the G Code for each file ??

« on: March 01, 2012, 02:44:14 AM »

Thank you BR549 , it works, (even it takes a long time to load the file), this is what I need. Fast solving problems.Thank you again.

UH

9

G-Code, CAD, and CAM discussions / Re: Total lines in the G Code for each file ??

« on: February 29, 2012, 12:42:26 PM »

Thank you Tweakie ,

I want to put this macro in the open file button to give me the total lines in the file ( automatic) as a OemDro .
I will use it for percent program process.(which give me % of the job finished).

UH

10

G-Code, CAD, and CAM discussions / Total lines in the G Code for each file ??

« on: February 29, 2012, 11:43:56 AM »

Hello

I would like to know if there is a Gcode or macro to give me the total numbers of the lines for each file I open in mach3 ??
In other words, I want a dro or input to show me the total lines for the file in the mach3 page.

Regards,
U.H