Messages

1

Promote and discuss your product / RobotDigg Equip Makers

« on: September 09, 2016, 09:43:16 PM »

How do you use a MKS Gen V1.4 Main Board for CNC?
http://www.robotdigg.com/product/945

2016, RobotDigg Equip Makers!
RobotDigg are trying to do our best to equip makers of Robotics, Drones, Open PnP, 3D Printer, 6 DOF
Wish all of makers come with brilliant kickstarter project.

2

Promote and discuss your product / RobotDigg Equip Makers

« on: September 03, 2016, 04:41:06 AM »

2016, RobotDigg Equip Makers!
Stepper Motor, Linear Stepper Motor, Geared Stepper Motor, Hollow Shaft Stepper Motor
Pulley n Belt, Ball Bearing n Linear Bearing, Ball Screw n Linear Rail
XYZ, CoreXY, Delta Robot of Kossel n Rostock, Scara, 6 DOF
RobotDigg are trying to do our best to equip makers of Robotics, Drones, Open PnP, 3D Printer, 6 DOF
Wish all of makers come with brilliant kickstarter project.

3

Promote and discuss your product / UIROBOT Stepper Driver and Stepper Controller

« on: July 26, 2011, 03:52:43 AM »

Contact Sales Manager Tiger Huang uirobot@yahoo.com or tiger@uirobot.com for details.
UIROBOT from Shanghai manufacturer of Miniature Stepper Driver and Stepper Controller products.

4

General Mach Discussion / Re: Can Mach3 work on stepper driver with RS232 interface

« on: April 25, 2011, 05:20:29 AM »

With many thanks to Stirling, that's really helpful to me a newbie

5

Promote and discuss your product / Re: Integrated Stepper Motor with Drives compatiable with Mach3

« on: October 27, 2010, 04:41:09 AM »

Hello everyone here, this is Tiger Huang product manager of stepper controller and stepper driver for integrated stepper motor from UIROBOT. It was demonstrated on Mechmate3 using Mach3. tiger.huang@uirobot.com for more information.

6

Promote and discuss your product / Re: Integrated Stepper Motor with Drives compatiable with Mach3

« on: October 13, 2010, 05:56:23 AM »

Hi,

Nice product!
This is mostly a hobbyist forum so if you publish data (supply voltage, current, pinout etc.) and if possible price + shipping cost to europe and USA you will get more customers!

Thank for reply, please contact us by e-mail tiger@uirobot.com and you could also buy from our Euro and US dealers.

7

Promote and discuss your product / Re: Integrated Stepper Motor with Drives compatiable with Mach3

« on: October 13, 2010, 03:39:37 AM »

S Curve ACCEL and DECCEL, SENSOR Input and Output

8

Promote and discuss your product / Re: Integrated Stepper Motor with Drives compatiable with Mach3

« on: September 15, 2010, 10:59:30 PM »

integrated stepper motor with drives will save cables, even control box.
Textile machines and pharmaceutical machines with many many motors, integrated stepper motor could avoid complicated wiring.

9

General Mach Discussion / Re: Can Mach3 work on stepper driver with RS232 interface

« on: September 13, 2010, 04:13:15 AM »

Thanks! But how could Mach3 work with XYZ or more than three-axis serveral parallel port drives?

10

General Mach Discussion / Can Mach3 work on stepper driver with RS232 interface

« on: September 13, 2010, 01:58:12 AM »

Someone told me that Mach3 just can work with parallel port stepper driver, is it right?
If I have a stepper controller with RS232 interface or CANBus, how could use Mach3 software? Thanks