Messages

1

Finished Screens / Re: Mach3 2010 Screenset - Now available

« on: September 27, 2015, 08:44:52 PM »

I must have a modified 890 Macro.  I found the copy of the 890 I have been using on my labtop and put it in the Marco folder and its working fine.   Thanks for your quick response and information.

Bryan

2

Finished Screens / Re: Mach3 2010 Screenset - Now available

« on: September 27, 2015, 05:05:43 PM »

Yes I did copy the files to the macro profile name.  When I press the laser zero button I get the value programmed into Marco 890 displayed on X and Y Coordinates but no movement


Bryan

3

Finished Screens / Re: Mach3 2010 Screenset - Now available

« on: September 27, 2015, 02:38:07 PM »

Gerry,  I had to re-load my whole computer again and cannot get the zero to Laser to work.  I push the button and nothing happens.  M8 does turn on the laser but when I go to zero to laser nothing occurs.   Running 3.043.066 Mach.
 Thanks, Bryan

4

Finished Plugins for Download / Re: Huanyang VFD controller plugin

« on: April 23, 2010, 07:35:53 PM »

Well I think it is time to step back and then come back to this in a few weeks with a fresh mind.  I have 4 different types of USB-485 devices and no luck.  Almost the same results.  Now my head is hurting and I think it is time for a beer.  Thank everyone for your assistance I have not gave up just took a break before I get a big hammer out and have to buy a Hitachi VFD.

5

Finished Plugins for Download / Re: Huanyang VFD controller plugin

« on: April 23, 2010, 02:10:15 PM »

michel pet ,

Michel,  if you would please post what you found to make your USB device work.  Please include screen shots of your port setups.

Thank you,

Bryan

6

Finished Plugins for Download / Re: Huanyang VFD controller plugin

« on: April 22, 2010, 10:12:05 AM »

Matty Zee,

Once again thanks for your assistance.  I made some voltage measurements with a volt meter, and O-scope and it appears that my converter dead out of the box.   I have a few more on the way that where posted as possible working converters.  I will post more when they arrive but they are on the slow boat from China.

7

Finished Plugins for Download / Re: Huanyang VFD controller plugin

« on: April 17, 2010, 10:33:50 PM »

I am using the suggested setup
PD001 2
PD002 2
PD163 1
PD164 1
PD165 3

Thank you for your assistance.

8

Finished Plugins for Download / Re: Huanyang VFD controller plugin

« on: April 17, 2010, 03:23:22 PM »

Matty Zee,

In one of the post you wrote "Many of these VFDs are missing relays, temp sensor etc, maybe yours is missing the RS485 transceiver chip?"   I have looked throw the VFD and I am missing the "Multi-Output FC FA FB relay" and their is a location on the first board that is missing a surface mount semiconductor chip"  Do you or anyone know the location of the RS285 transceiver chip.  Another question is does any one have a schematic for this device?  I made the changes you suggested last night and Mach sent 01 03 01 08 F1 8E and received 7F 7E 7F.  Another interesting thing is a few seconds after pushing the spindle button I received a E-stop.

9

Finished Plugins for Download / Re: Huanyang VFD controller plugin

« on: April 16, 2010, 08:30:06 AM »

Thanks for clearing that up.  I will post latter to day when I get of work.

Thanks,

bolingerbe

10

Finished Plugins for Download / Re: Huanyang VFD controller plugin

« on: April 16, 2010, 08:15:35 AM »

Matty Zee, just to make sure I understand you.  You want me to uncheck PD002.  Is that correct?