Hello Guest it is May 16, 2021, 02:02:02 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - saintr

Pages: 1
1
One on one phone support. / Phone Support Please
« on: October 29, 2012, 08:06:49 PM »
Hello,

We've been having a couple issues with a fresh installation of Mach3 on a new machine. After reading through many posts and submitting a couple of our own we've had no success fixing them. We need to get this resolved ASAP. More info is below:

Problems:
1. Z-axis levels are not being displayed in Mach3 viewer, all Z-axis paths are flat on X-Y plane. They appear fine on our other Mach3-Gecko machines.
2. Mach 3 suddenly stops running 1/2way through G-code program (same place each time)

Email:
info@conduitprojects.com

System Info:
Intel Atom D2700 Mini-ITX
60GB SSD
Windows 7 32-bit
Parallel port pre-installed
Xylotex control unit and NEMA 23 motors
Mach3 was installed following Win-7 directions from Forum

Thanks,
R

2
Mach Screens / HELP! Z-Axis is Being Flattened out onto XY-Plane
« on: October 05, 2012, 05:42:16 PM »
Hello,

We just set up our third Mach3 CNC machine, a Mini-Mill driven by a Xylotex box, the computer is an Intel Atom with Windows 7 32-bit and a native Parallel Port. We installed the memroyoverride.reg as outlined in previous posts for using Mach3 on Vista/7. G-code is being generated by MadCAM in Rhino with minimal issues on other machines before.

Today we opened the first G-Code on the machine in Mach3 and we've run into something we've never seen before and are having trouble finding the cause. I spent the second half of the day trolling the internet for a solution but nothing yet.

The problem is the G-Code in Mach3 is being flattened out onto the XY plane. It looks fine in Rhino and on the other machines (images attached) but it's smashed flat in the Mach3 running the new machine. I'm sure we just missed one of the zillions of settings to make it work correctly, sorry in advance if it's something dumb...

Thanks

3
FYI, did some more digging and found a possible iron clad solution for all those of use trying to make the second PP thing work: http://www.pmdx.com/2PARPCI

I've ordered one and will post a review after it arrives...

4
I'm having very similar issues and have read through tons of threads on this and other CNC forums with no luck. Have a Dell Optiplex 170L w/ XP 32-bit running a Gecko G540-G251 5-axis setup through 2 parallel ports (PP). The main PP goes to the G540, the auxiliary PP (was just added in PCI slot) runs the G251. All the Mach 3 settings seem to be ok and the 4 steppers running on the G540 w/ main PP work fine. I can't get the aux PP to work. It says it's SPP/ECP/EPP compatible but I can't set it to EPP individually in the setup menu upon booting. I've uninstalled and reinstalled drivers, tried swapping ports, motors, reinstalled a fresh copy of Mach 3, nada...

Reading around, it seems I may have to get a computer with ISA expansion ports for the aux PP or try my luck with various brands of PCI PP cards... Anybody out there have a definitive answer/solution?

Much obliged,
Robert

5
General Mach Discussion / Re: Coordinates are wrong
« on: July 24, 2009, 10:49:18 AM »
I haven't set it to any microstepping. I will check with Xylotex on that. As far as setting it to mm, I have set the default units to inches nearly a dozen times now.

Thanks

6
General Mach Discussion / Re: Coordinates are wrong
« on: July 24, 2009, 10:31:09 AM »
Screws are:

3/8-10, 2 start for Y and Z axes
1/2-10, 2 start for X axis

They are all driven by Xylotex 425 oz.in. steppers at 200 SPR with no gearing, they're all 1:1 pulley-belts.

Thanks

7
General Mach Discussion / Coordinates are wrong
« on: July 24, 2009, 10:14:02 AM »
Hi everyone,

I saw a previous post asking about Mach3 sowing "massively wrong" coordinates but there were no replies that adequately answered the question. I have built a 60" x 48" x 9" CNC router, got through the first two tutorials, set units to inches, entered in all the motor tuning information according to the correct motor-leadscrew ratio (1000 SPI, 126 IPM, 90 accel). When I jog the router I get coordinates appx 6x the amount actually traveled. Please let this newbie know what he's doing wrong.

Much appreciated

Pages: 1