Hello Guest it is November 20, 2019, 04:03:23 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - frmoul

Pages: 1 2 3 »
1
Hello,

I don't know about the spindle.

For the home switch, I guess you must setup them on input as they are plug in with the nc pod.


Freddy

2
Hello,

I just checked on the PC which drive my machine :

Ouput :
For X, Y, Z :
Step  : 1 Dir port : 1


Input :
E stop : Port#1  Pin#2
As I don't put switch for end of stroke, I only specified a setup for e stop for input setup.

All parameters don't write in this answer is at 0 or enable status.

My spindle is a Kress without driving stuff from the card.

Freddy

3
NC Pod / Re: status of NCPod
« on: December 25, 2010, 03:02:41 AM »
Hello,

I just checked on the PC which drive my machine :

Ouput :
For X, Y, Z :
Step  : 1 Dir port : 1


Input :
E stop : Port#1  Pin#2
As I don't put switch for end of stroke, I only specified a setup for e stop for input setup.


All parameters don't write in this answer is at 0 or enable status.

Freddy
 

4
Hi,

I have not my machine with me.

I could reply to you on 24th december, I could check on the PC which drive my machine.
Send me a message to make me remerber on the 24th that I have to give you this answer if you did'nt have it from another person.

Regards

Freddy

5
General Mach Discussion / Re: Problem configuring ncpod
« on: May 30, 2009, 01:23:02 PM »
Hello all,

my 3 motors can run under mach3 now !

I had two principal problems :

- I used an usb drivers not good with mach3 (Carl from Oemtech help me a lot about that)
- my drivers don't have to be connect as a Gecko driver, so ncpod manuel wasn't enough precise for the connection type I needed, but Carl gave me information I needed.

I took a long time to identify and resolve problems, but that's done now !

The machine will run soon, even if its not completely finished.


Regards

Freddy

6
General Mach Discussion / Re: Problem configuring ncpod
« on: May 16, 2009, 03:23:03 AM »
HI all,

Yes I send some emails to the manufacturer. For my first problem (manage to have a good communication between ncpod and mach3, its help and yours was both necessary. I used a driver for ncpod basic panel which is not suitable for mach3.

Machine master, I will read again the links you advise me to try. Perhaps I haven't see something in.

Freddy

7
General Mach Discussion / Re: Problem configuring ncpod
« on: May 15, 2009, 05:23:27 PM »
Hi Hood,

I already try that, I check again, but unfortunately, it dont change votage when I choose Active Low or not.

I don't understand why I notice this kind of problem on motor output on ncpod.


Freddy

8
General Mach Discussion / Re: Problem configuring ncpod
« on: May 15, 2009, 02:57:59 PM »
Thanks Greolt

I have this diagram.

I tried parameters of a guy on youtube that have same gear than me, but that's not the problem in fact.
If I mesure tension with a plaine multimeter, tension for pulse is always 5V when I puch jog button to make move an axis and when I don't! I mesure this tension directly on ncpod. I don't undestand why.

I guess that when I don't "ask" mach 3 to send pulse, tension have to be 0 V! Is that true?

Freddy

9
General Mach Discussion / Re: Problem configuring ncpod
« on: May 14, 2009, 04:45:35 PM »
Unfortunatly,  I didn't find the answer to my problem yet.

However, I thank you again to contributing to that.


Freddy

10
Hi all,

is any body has answer to my problem there : http://www.machsupport.com/forum/index.php/topic,11533.new.html#new  ?

Freddy

Pages: 1 2 3 »