Hello Guest it is April 01, 2020, 07:55:16 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - sledrat

Pages: 1 2 3 »
1
Mach3 under Vista / mach3 gone
« on: November 30, 2014, 04:20:48 PM »
hi everyone thi maybe a long post so please bear with me
i have a 2008 cam wood wr404 bought new and love it
my issue is this my dell desktop crapped out last night without a hint of trouble after 6 years of great work never even a single glitch
after going through all the tests i had to replace the hard drive
now for the reinstall of the mach
i have (2) html files i belive 1 maybe the original mach3 and the newer dated very close to the time i bought my machine
i am in hopes that cam wood will give me a copy of my license # and be able to re install it
so all that being said are the html codes basically my specific machine parameters ????
if so how do i go about incorporating them when i download a new copy of mach 3 ???
i am running vista and through one of the things i read my version of mach3 was1.87any help would be great

2
General Mach Discussion / Re: long program glitch
« on: December 06, 2009, 08:35:26 PM »
hey guy i want to thank you again
tommorow i am going to try to program a simple fileand try different tool changes
and i am going to check all my settings if i read your post rite its late where ever you are from
get to sleep

 

3
General Mach Discussion / Re: long program glitch
« on: December 06, 2009, 08:25:31 PM »
yes its supposed to

4
General Mach Discussion / Re: long program glitch
« on: December 06, 2009, 08:24:55 PM »
i dont use the tool table because i am running only a few bits and on my machine when ever you change to a different tool number it brings up a pop up that says you can only have tool num 1

5
General Mach Discussion / Re: long program glitch
« on: December 06, 2009, 08:20:54 PM »
or do you know of a simple do nothing file that would involve multiple tool changes i could run as an example
that way i eould know what to expect or at least know ho to modify my txt file to suit my machine
about the onle code i use now is g64 constant vel so its not to hard on my machine

6
General Mach Discussion / Re: long program glitch
« on: December 06, 2009, 08:14:59 PM »
i guess that tells me mine might have an issue
can you tell me the correct way to deal with vetricthat uses different tools
and my machine that does not have a tool changer or at least tell me what is supposed to happen

7
General Mach Discussion / Re: long program glitch
« on: December 06, 2009, 08:08:49 PM »
hey i have seen that my file i belive it is the standard
i have seen the file mach3mill.xml some where on the cnc pc

8
General Mach Discussion / Re: long program glitch
« on: December 06, 2009, 07:58:23 PM »
hey by the way i want to thank you for your help

9
General Mach Discussion / Re: long program glitch
« on: December 06, 2009, 07:57:23 PM »
in the space next to reset it says emergency and scrools rite to left repeating

10
General Mach Discussion / Re: long program glitch
« on: December 06, 2009, 07:51:00 PM »
stop  for a tool change but that is when truble happens
i would like to enter the offsets page change tools and hit the start cycle and walk away for the next 20 min.
but what i get is the machine stops then either before or after i go to the offset page to change tools
i get an emergency

Pages: 1 2 3 »