Hello Guest it is November 29, 2022, 02:43:11 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - vertcnc

Pages: 1 2 »
1
General Mach Discussion / Re: Options for Lathe Retrofit
« on: February 20, 2015, 06:00:39 PM »
Hood,

Thanks for the info.  I did look at the some of the Mentor drives on ebay in the US and they can get pretty expensive in the $1500 to 2500 USD range.  That's an option if something comes up.  I was thinking of a Sensorless Vector AC drive which should have good low end torque.

CS-Labs would be my choice.   I would like to keep the current servos and drives just have to see what condition there in.

Thanks for the info.

2
General Mach Discussion / Options for Lathe Retrofit
« on: February 20, 2015, 09:57:11 AM »
Just looking for some options for retro-fitting Mach 3 or 4 to and older lathe.

It currently has a Siemens 5 HP DC servo and drive for the spindle. 200V 3 phase input, most likely analog control.  Encoder coupled to Spindle.  My thoughts were to replace the DC servo with a AC motor and VFD and retaining encoder on spindle, just because of the voltage and unknown condition of current servo/ drive.  Would I be able to sync spindle to axis for threading?  What capability would I be losing besides positioning?

Turret and closer are hydraulic with solenoid control and some type of rotary switch for the 8 turret positions.


What's my best options for control, as far as breakout boards?

Thanks

3
Modbus / Re: Mod Bus VFD control and smooth stepper ethernet
« on: December 01, 2014, 07:39:36 PM »
John,

Yes, you can use Mobus and also use a smooth stepper.  I am using serial Modbus to control my VFD via Brain. Ethernet Smooth stepper for motion control and I/O. I am probably not the best guy to instruct you, had to stumble through the whole Modbus-Brain configuration.  I am sure someone here can help you once you get ready.

4
General Mach Discussion / Re: Semi-Rigid Tapping
« on: April 18, 2014, 07:09:35 PM »
Peter,

This appears to have done the trick.

Thanks

5
General Mach Discussion / Re: Semi-Rigid Tapping
« on: April 16, 2014, 08:21:47 AM »
Peter,
I will give it a try.  The problem is it appears that the spindle starts just fine, but it is the next line of code that retracts the spindle that there is a dwell or lag. Doesn't matter if I change the dwell or remove the line od code completely.

Tim

6
General Mach Discussion / Semi-Rigid Tapping
« on: April 15, 2014, 07:37:02 PM »
I am experimenting with my T/C tapping holder and it appears that there is a delay in retracting the head after the swindle starts.  I am running the spindle via VFD and Modbus.  ESS for machine control. After the spindle starts in the CCW direction there is a delay until the head starts moving up. Don't know if there is a setting in ESS or Mach3 that can correct this lag.
Here is a sample of the code.


(Tap: 1/4 20)
N01 G90 G80 G40 G54 G20 G17 G50 G94 G64 (Safety block)
N02 M5
N05 M9
N10 T50 M6
N20 M3 S400 (Spindle on CW)
N30 G0 X.287 Y-1.06 Z.1 (Rapid to Above 1st Hole)
N40 G1 Z-.25 F20 (Begin Tapping 1st Hole)
N50 M4 S400 (Reverse Spindle Direction)
N60 G4 P.0 (Dwell, 0.5 Second)
N70 Z.1 F20 (Retract)
N80 M3 S400 (spindle on CW)
N90 G4 P.5 (Dwell, 0.5 Second)
N100 G0 X1.037 Y-1.06 (Rapid to Above 2nd Hole)
N110 G1 Z-.25 F20 (Begin Tapping 2nd Hole)
N120 M4 S400 (Reverse Spindle Direction)
N130 G4 P.0 (Dwell, 0.5 Second)
N140 Z.1 F20 (Retract)
N150 M30 (Program End)

7
General Mach Discussion / Re: Mobus and Durapulse GS3 VFD Help
« on: January 10, 2014, 09:30:55 PM »
Ok, I figured out the address for reading the drive status and displaying the data to userdro's. Still can figure out what address for output. Any help would be appreciated.

8
General Mach Discussion / Mobus and Durapulse GS3 VFD Help
« on: January 09, 2014, 11:17:40 PM »
I would like to control the GS3 via Modbus. I have the rs485 connected and appears Modbus communicates without error. I having a problem understanding the settings for start reg and # of registers. it appears I can read on the input side on start reg 0 I can read 7 registers. How should the output be setup to control spindle.  I also would like to map the inputs to User DRO's to display RPM, AMPS, Freq. if possible.


 http://www.automationdirect.com/static/manuals/gs3m/ch5.pdf

Can I do this with some VB scripts or is a Brain required.

9
+1 on posting the code. I am also building a 10 position ATC for my RF45 and could use some help with the macro side of things.

10
General Mach Discussion / Re: Tool changer control
« on: June 20, 2013, 09:40:03 AM »
Thanks Derek for the link.  I think I could figuire out the macro, just was curious if unloading this task to a micro controller would have any advantages.

Pages: 1 2 »