1
General Mach Discussion / feedrate & units per min are different
« on: October 22, 2008, 11:10:58 PM »
After a tool change, the speeds specified by the Gcode seem to be ignored and the speed in "motor tuning" is used. Before the tool change everything works as planned. I am using the latest legacy mach 3 and Gcode from RhinoCam. I have mach3 set to stop and wait upon tool change.
It happened specifically here:
X-0.4673 Y-0.1964
X-0.5287 Y-0.3053
Z0.1250 F15.0
(Deep Drill )
G00 Z0.0000
G00 X0.0000 Y0.0000
M6 T8
M03 S10000
X0.0000 Y0.0000 Z0.1141
G83 X0.0000 Y0.0000 Z-0.3 R0.1 Q0.05
G80
G01 Z0.1141 F4.0
(2 1/2 Axis Pocketing)
G00 Z0.0000
G00 X0.0000 Y0.0000
M6 T2
M03 S10000
X-0.1066 Y-0.1975 Z0.0312 F15.0
Z-0.0196 F1.0
X0.1066 F3.0
X0.1177 Y-0.1911
X0.2244 Y-0.0064
Y0.0064
X0.1177 Y0.1911
X0.1066 Y0.1975
X-0.1066
X-0.1178 Y0.1911
X-0.2244 Y0.0064
Y-0.0064
X-0.1177 Y-0.1911
X-0.1066 Y-0.1975
Z-0.0392
X0.1066
X0.1177 Y-0.1911
X0.2244 Y-0.0064
Y0.0064
X0.1177 Y0.1911
X0.1066 Y0.1975
X-0.1066
Instead of deep drilling at 4 ipm, it did it at my Z motor tune speed of 12.... Then instead of profiling at 3 IPM it went at 20. The FRO says the correct speed... but units/min says the motor tune speed...
Is there some setting in general config I may be missing?
It happened specifically here:
X-0.4673 Y-0.1964
X-0.5287 Y-0.3053
Z0.1250 F15.0
(Deep Drill )
G00 Z0.0000
G00 X0.0000 Y0.0000
M6 T8
M03 S10000
X0.0000 Y0.0000 Z0.1141
G83 X0.0000 Y0.0000 Z-0.3 R0.1 Q0.05
G80
G01 Z0.1141 F4.0
(2 1/2 Axis Pocketing)
G00 Z0.0000
G00 X0.0000 Y0.0000
M6 T2
M03 S10000
X-0.1066 Y-0.1975 Z0.0312 F15.0
Z-0.0196 F1.0
X0.1066 F3.0
X0.1177 Y-0.1911
X0.2244 Y-0.0064
Y0.0064
X0.1177 Y0.1911
X0.1066 Y0.1975
X-0.1066
X-0.1178 Y0.1911
X-0.2244 Y0.0064
Y-0.0064
X-0.1177 Y-0.1911
X-0.1066 Y-0.1975
Z-0.0392
X0.1066
X0.1177 Y-0.1911
X0.2244 Y-0.0064
Y0.0064
X0.1177 Y0.1911
X0.1066 Y0.1975
X-0.1066
Instead of deep drilling at 4 ipm, it did it at my Z motor tune speed of 12.... Then instead of profiling at 3 IPM it went at 20. The FRO says the correct speed... but units/min says the motor tune speed...
Is there some setting in general config I may be missing?