Hello Guest it is March 28, 2024, 11:30:58 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - nilesh

Pages: 1 2 »
1
General Mach Discussion / mach3 for laser
« on: November 05, 2008, 07:27:27 AM »
Dear all,
      We are trying to using the dmc 2123 controller(galil) and mach3 software for laser system.
      We saw setting for mill in mach3. But we are not able to get proper setting to interface laser.
      We only need to one out put from mach3 to turn on or off laser
       Please provide the detail solution as soon as possible.

Thanks Regards,
Nilesh Deshmukh
exceltech southasia
Andheria,(E),Mumbai
Mumbai, Maharastra  400068
India
Phone: 91-022-28222323
nilesh@exceltech-southasia.com


2
General Mach Discussion / Re: problem limit switch motion
« on: October 23, 2008, 06:41:53 AM »
i have set auto limit override button. then i try to move motor after limit interrupt using ( up/down button ) joging .
but didnot work.

3
General Mach Discussion / Re: problem limit switch motion
« on: October 23, 2008, 05:50:10 AM »
thanks hood
auto limit works for galil.
can you give the detail path where i can set auto limit override option.

4
LazyCam (Beta) / motion at complex curve line
« on: October 23, 2008, 01:36:43 AM »
hi all
i am using the galil 2123 controller with mach3 software.

my question is about motion at complex curve line at this point motion speed should be slow. so  how would i can adjust the slow speed at curve motion using lazy cam.

5
General Mach Discussion / problem limit switch motion
« on: October 23, 2008, 12:54:49 AM »
hi all
i am using the galil 2123 controller with mach3 software.
i have problem limit switch. when ever my limit switch interrupt my hole motion get stop even my reverse,forward motion.
example:  if my reverse limit interrupt my motion get stop then i am not able to move motor in forward/reverse direction.
again i have to manually reset my limit switch by moving motor manually.
please provide the solution.

6
General Mach Discussion / Re: homing does not show the 0 position
« on: October 20, 2008, 03:12:15 AM »
hi sir
      i have enable the home switch in port and pin setting.(i am using mach3 with galil). does this make any problem.

7
hi
 i am using gail 2123 controller with mach3 software.
i want my motor should stop exactly when limit/home interrupt without chaining the my acceleration, deceleration setting.
please provide the solution.   

8
General Mach Discussion / Re: homing does not show the 0 position
« on: October 18, 2008, 07:09:49 AM »
your you are saying partially write.
my homing action take place correctly( my motor stop at home). but after that  mach3 window suppose to show the 0 position but rarely it does not show 0 position.
yes it is controlled via galil. but in galil samrt terminal software homing action take correctly with showing position zero.
can explain the custom Ref All button.

9
General Mach Discussion / homing does not show the 0 position
« on: October 18, 2008, 05:13:39 AM »
hi all
i am using the galil 2123 controller with mach3 software.
some time after pressing the home Reference home button  " homing indication" on mach3 window does not show the 0 position.
 i did the setting in home/limit configuration.
please provide the solution.

10
LazyCam (Beta) / autocad dxf file can feed to lazy cam software
« on: October 18, 2008, 01:17:56 AM »

i am new in this lazy cam software.
i just want to ask autocad dxf file can feed to lazy cam software.
if there is predefine procedure please suggest me

Pages: 1 2 »