Hello Guest it is February 28, 2020, 03:12:52 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Edmund

Pages: 1 2 »
General Mach Discussion / Re: Program crash
« on: May 03, 2019, 02:52:54 PM »
Thank you, Reuelt,

 Yesterday I managed to get the program back after the crash I think the problem was that the Feed adjustment was somehow locked and reading 1% and when trying to reset to 100% it was not responding it would go up to 80% and then drop back to 1%,

Appreciate your suggestion and will certainly do that,

Thanking you, Edmund........Alberta

General Mach Discussion / Program crash
« on: May 02, 2019, 02:19:27 PM »
Running XP stand alone version R3.043.066 everything has gone haywire and status window says cannot reverse run from present feedhold

Can any member give me a clue

General Mach Discussion / Re: Need Help re: download
« on: October 25, 2009, 10:11:37 PM »
   I have been running Mach3 on a computer capable of producing excellent results, unfortunately I contacted a very nasty virus a Trojan and others, my question is, would it be possible to do a complete download of XP, would that clear the virus, or would it destroy my XP CD by transferring the virus onto the XP CD,


General Mach Discussion / Re: Need Help re: download
« on: October 25, 2009, 08:43:57 PM »
Ray can I ask you a different question?, relating to a virus in computer?

General Mach Discussion / Re: Need Help re: download
« on: October 25, 2009, 08:36:34 PM »
Thanks Ray,
      I kinda guessed that was the reply I would get, thanks anyway,


General Mach Discussion / Need Help re: download
« on: October 25, 2009, 07:22:28 PM »
Mach3 into old computer,

Mitra clone (I think?), 133 megahertz, Pentium 1 (Ithink), Windows 98 second edition,4.10.2222A, 40MB RAM,

I tried downloading Mach3 R3.042.029, no good unable too, I'm not a wizz at computers, my question is, if I download windows XP (if I can?) will that enable me to load Mach3?,

I have Master5 loaded at this moment,


LazyCam (Beta) / Re: problem with lazycam
« on: October 23, 2009, 10:41:46 PM »
Have look at the LazyTurn Manual - Appendix "B" located in Members Docs. I t talks about common mistakes made in CAD.  The errors are generic.

Hello Rich,
       my apologies for not getting back to you sooner, I've had a few busy days here, right now I am going to take your advise and check out the lazycam manual,

Thank you for your response to my predicament.............Edmund.........

LazyCam (Beta) / Re: problem with lazycam
« on: October 23, 2009, 10:24:40 PM »
Hello Chip,
      tried out the gcode for the distributor rocker, matl used as a test was Delrin, the finished sizes were spot on, I will probably make the real part from Bakerlite or Tufnol, I would like to thank you for getting me going, and at the same time I have picked up a few learning curves for myself,

When I get the parts finished and assembled I will attach a photo, in the mean time here are a couple of photos attached to give you some idea,

Again thank you,.........Edmund.........

LazyCam (Beta) / Re: problem with lazycam
« on: October 22, 2009, 10:28:22 PM »
this is the rocker

Hi, Edmund

Try this one also.


LazyCam (Beta) / problem with lazycam
« on: October 22, 2009, 12:03:16 AM »
sending a drawing in dxf autocad 2000

Pages: 1 2 »