Hello Guest it is March 29, 2024, 08:46:18 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - dacostad

Pages: 1 2 3 4 5 »
1
General Mach Discussion / Re: Softlimits question
« on: February 16, 2010, 08:00:30 PM »
Yep, just fired of an email to them.

Thanks for all your help.

David

2
General Mach Discussion / Re: Softlimits question
« on: February 16, 2010, 07:40:17 PM »
No brains enabled.

You are right though it is a plugin for my MPG pendant from VistaCNC.com.

If I disable it, and restart Mach3 I do not get the message. If I then enable it I get the message straight away.

I guess I will need to check with VistaCNC

Thanks

David

3
General Mach Discussion / Re: Softlimits question
« on: February 16, 2010, 05:09:27 PM »
I am thinking it may be something to do with the screenset you are using, unfortunately I can not open your xml with that screenset as I dont have the licence for it. However when I changed to the standard screenset it opened fine and there was no soft limit warning. I suggest you email Jason (Zealous ) and see if he can give you some help.

Hood

Yes, I had the same thought, so I tried it with the standard default Mach3 screen and got the same result.

David

4
General Mach Discussion / Re: Softlimits question
« on: February 16, 2010, 02:20:26 PM »
Here it is.

David

5
General Mach Discussion / Re: Softlimits question
« on: February 16, 2010, 02:14:46 PM »
y max 13 min 0
x max 5.9 min 0
z max 0 min -11.35

I get the message when I start up Mach 3,  if I clear it, I only see it again if I move to one of the softlimit limits which is what I would expect.

David

6
General Mach Discussion / Re: Softlimits question
« on: February 16, 2010, 01:45:17 PM »
Hi Russ, I already have macro pump unchecked, so it is not that.

David

7
General Mach Discussion / Re: Softlimits question
« on: February 16, 2010, 12:06:53 PM »
Nope, just G80.

David

8
General Mach Discussion / Softlimits question
« on: February 16, 2010, 11:00:27 AM »
I use softlimits on my Novakon Mill and whenever I load Mach 3 I get a "Softlimits System Movement Aborted" message in the status bar before I do anything  including referencing the mill.

Can anyone tell me what this means and why is it occurring?

Thanks

David

9
General Mach Discussion / Re: Strange circle problem
« on: December 07, 2009, 09:25:33 PM »
No backlash or backlash compensation.  I think it might have been the gib, as I removed it completely, cleaned it and re-inserted it and from a quick test cut it looks better.

I will test further tomorrow,

THanks

David

10
General Mach Discussion / Strange circle problem
« on: December 07, 2009, 08:51:19 PM »
I have a Seig KX1 (LMS version) and all of a sudden it is behaving strangely cutting circles.   The top and bottom of the circle is flat rather than a smooth circle.  It is like at the top and bottom the y axis has stopped moving.  This is repeatable and is always a perfect horizontal flat.  I have adjusted the gib on the y axis but it is still the same.   Is there anything else that could cause this?

Thanks


David

Pages: 1 2 3 4 5 »