Topics

1

Tangent Corner / 5axis cnc engine block

« on: March 23, 2007, 01:10:11 AM »

WOW!
<a href="http://www.youtube.com/v/QsmiIeAkE-o" target="_blank" rel="noopener noreferrer" class="bbc_link bbc_flash_disabled new_win">http://www.youtube.com/v/QsmiIeAkE-o</a>

2

Tangent Corner / DYI Rapid Prototyping

« on: February 06, 2007, 02:12:10 AM »

Check It out.

http://www.fabathome.org/wiki/index.php?title=Main_Page

3

Tangent Corner / Sears Craftsman CNC router

« on: January 01, 2007, 06:30:41 PM »

Has anyone seen the TV ad for the Sears Craftsman CNC router around  $1900.00. What do you think?

4

General Mach Discussion / Stuff for sale were to post

« on: December 17, 2006, 11:37:53 PM »

Are we allowed to post stuff for sale on the mach board? If so were?

Thanks

John

5

General Mach Discussion / blue screen of death

« on: October 19, 2006, 10:56:55 PM »

Here we go again. What causes the blue screen of death when you load Mach 2/3?

I need to sort out my touch screen but i cant get around this. I tried uninstalling the drive serval times and reloading mach also but i just cant figure it out. im sure is something simple.  I'm running win200.

any ideas would be appreciated.

6

General Mach Discussion / mach2 demo and mach3

« on: October 19, 2006, 08:51:01 PM »

is mach 3 a demo like mach 2 and limited to a 1000 lines of code?

7

General Mach Discussion / Wrong Driver error

« on: October 18, 2006, 07:49:45 PM »

When i start mach 3 i get a wrong driver error on my screen? Are their different drivers or am i doing something wrong?
im running win2000.

8

Mach Screens / Screen designer

« on: October 15, 2006, 10:31:37 PM »

If i open an existing screen in screen designer4 and resize all the items to fit 800x600 will that work. I don't want to reinvent the wheel i just want to resize an existing screen to fit my touch panel.

9

Screen designer tips and tutorials / Screen size

« on: October 14, 2006, 09:08:52 PM »

How do you specife screen size in screen designer? Or do i just lay out all my button to fit in 800x600 size?

I been practing screen designs and im ready to start but i just want to make sure the work I do will fit my final screen size fro my touch scree.

Never mind i watched the video tutorial and the fisrt thing was a screen size check box

10

General Mach Discussion / Breakout board from Bob Cambell Design.

« on: October 13, 2006, 10:45:28 PM »

I put 120v through my board and printer port and Bob Campbell and Jim from Sound Logic replaced it for free even though i smoked the thing, actually burnt traces off the board.(DUH, Hopefully Sony will be that understanding about their laptop.)

Not only is the board top notch they really support their products.

SO BUY YOUR BREAKOUT BOARD FROM THEM!

NUFF SAID!

Here's the e-mail i got from them.
 
I am sending you a new board by USPS priority mail today. See the note from Jim Cullins below.
 
Just send John a new one. I will replace it for him. The other one has all the chip blown and I would not trust it even if I replaced them.
Tell him that because he was honest in admitting what happened it is free from me.
 
Thanks
James Cullins

Robert Colin Campbell
Bob Campbell Designs
www.Campbelldesigns.com
Mach 2/3 breakout boards
Relay boards