Hello Guest it is February 28, 2021, 02:59:31 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - wakedabed

Pages: 1 2 3 »
1
General Mach Discussion / Motherboards And Mach3, questions..
« on: January 23, 2017, 12:35:21 AM »
Hello people,

Can someone explain to us what the difference will be between one motherboard 2Gh and another motherboard 4Gh? We talking about the same pc with win7 32-bit..
How mach3 will react with the two motherboards?

Thanks so much!

2
General Mach Discussion / In Reverse Run HELP!
« on: December 13, 2016, 02:36:42 AM »
hello people,
i want to ask if there are some led for g00??
because, when i want to reverse run the g-code (that contain lines start with g00/g01/g02/g03), and when i press STOP (do while running in reverse), if the line that i stopped was g00 to activate the specific led, and if its was something else to inactivate the specific led?

3
General Mach Discussion / ArcOK signal purpose please!!
« on: July 18, 2016, 04:00:52 PM »
Hello there,

Can someone tell what is the purpose of arcok signal?

I have a THC proma

4
Hello people,
I want to ask how this message work? How I can know the mechanism of this? I can put on my screen a LED that show me if my machine in G00 or in G01???? PLEASE HELP!!!

5
Hello people,

I have a C11GSD breakout board from cnc4pc and cap04 thc, on the breakout board I have 3 relays, I use just the first 2 relays, one for plasma and the second for flame.
When I write dooembutton(110) on my macro its ok the relay and the thc are working, but when I try to write Activate signal(output2) for the second relay, the thc not working!

Please help!

6
Hello people,

I have a C11GSD breakout board from cnc4pc, and now I trying to activate my CAP04 THC plasma, on the mach3 I can see the led of up and down fladhing but no movement of the z axis!
Can someone please help me with this problem?

Thanks so much!

7
General Mach Discussion / Can someone verify my wiring please?
« on: October 20, 2015, 06:16:54 AM »
Can someone verify my wiring please?
I have a PMDX-122  and M542 drivers motors

Thanks so much!

8
Hello people,

I have win 7 32 bit with tb6600 board and nema 24.
I have a problem when I slave A to Y, one of the motors run ok and smoothly but the ather motor run slowly with intermittent steps!
I have changed the motors but its still one of them moving bad!
I have tried to change my kernal speed and sometimes its going ok but when restart my Mach3, again the problem appear!! I didn't know what to do! Can someone please help me?

Thanks so much!

9
General Mach Discussion / Mach3 issues on Windows Xp! Please help!
« on: April 18, 2015, 06:03:13 AM »
Hello guys,

I have installed Mach3 on my windows xp 32-bit, after that I have observed some thing so strange, when I want to start up the windows, before done, it's stop suddenly without any notification and the screen like turn off!
Just after some times I try to restart it will open!

Can please some one help me please!
It's make me crazy!!

Thanks so much!
Best regards!

10
General Mach Discussion / How to choice the power supply?
« on: April 10, 2015, 01:28:39 PM »
Hello guys,

I want to ask how to choice the power supply that I wanna use on my machine?
For ex, how to choice the W or A or V?
Where to be careful when I want to choice it?

Thanks so much!
Best regards!

Pages: 1 2 3 »