Hello Guest it is March 28, 2024, 05:30:59 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - chuckels

Pages: 1
1
General Mach Discussion / home offsets
« on: January 27, 2009, 03:21:53 PM »
is there a way to have the table of the mill automatically go to a set position after homing.
I would swear the home offsets in the homing and limits did that in some older versions.
thanks,
Chuck

2
General Mach Discussion / slow motion if firefox is active
« on: April 05, 2007, 01:01:12 AM »
Brian,
why does everything go in slow motion if i try to run mach 3 while Firefox(internet browser) is open?
the screens scroll up very slowly in any progs that are open at the time.
I have to shut down Firefox and restart mach to get back to normal.
chuck

3
General Mach Discussion / loading screen sets
« on: December 04, 2006, 02:51:40 AM »
The instructions for loading screensets says " To use, select layout/load screenset and select the name of the set you downloaded."
 where is the layout/load option in mach3?
chuck

4
General Mach Discussion / new versions
« on: November 27, 2006, 01:37:44 PM »
Art, Brian,
WOW really doing a lot of great work on Mach 3, already up to .015.
whats new or repaired in .015 ? the last entry in the rev list is for v.011.
chuck

5
General Mach Discussion / License file not working in v2.0.0.11
« on: November 20, 2006, 09:07:46 AM »
Brian,
just upgraded to V2.0.0.11 and it comes up as demo ver, copied lic files to Mach dir with no luck also NS shows un-licensed also

6
General Mach Discussion / problem with V2.0004
« on: October 24, 2006, 06:12:24 PM »
Brian,
I did a clean install of V2.0004 and loaded a small part and the leadout is goofy
I reinstalled V2.000 and it is ok-- see picts
any ideas nothing else changed same xml.
chuck

7
General Mach Discussion / inserting pics in post
« on: October 13, 2006, 03:47:06 PM »
can someone tell me how you insert a photo into these posts? I see several posts with pict download buttons but cannot tell how its done.
thanks,
Chuck

8
Mach3Mill.xml is still being over written when I install the latest updates to Mach 3. this did not happen before versions "RC"
does this need to happen? sounds petty but curious what changed.

also is it necessary to reboot when doing upgrade or just on new install?

9
General Mach Discussion / RC2.0c rewriting XML file
« on: September 26, 2006, 03:14:06 AM »
I just installed MACH 3 V RC2.0c and it over wrote my old mill XML  file. :(
 is there some reason this needs to happen? I had my old XML backed up can I use it with the new ver or do I have to re do all the settings?
chuck

10
General Mach Discussion / Text engraving wizard save
« on: March 11, 2006, 07:19:34 PM »
Can any one help,
when I use the text engrave wizard it works fine in the current session but if I save the g-code with a file name and restart Mach 3 at a later time and reload the code it displays some of the text with large circles or swirls and tries to cut that path. this happens with Helvetica font ( which is one of the only single line fonts in it ) or any font that has smooth curves.
is it possible that something  is not being saved with the code that is set when the wizard is first run?

chuck

Pages: 1