1
Mach SDK plugin questions and answers. / Problems with probe set up and use
« on: October 12, 2013, 07:06:00 PM »
New and finally frustrated. I am sure I am missing something simple.
Here goes I installed the probe that came with my unit:
went to Config Port and Pins Input selected auto and it found it 1 13
Next I went into Config Config pugins looking for Probing 3d-digitising-Fenerty-Barker-Version-2.00.046. It wasn't there!
I than checked my Mach3 version number and it was R3.043.022
I was using older version installed it sometime ago than got sick and never got to set up or use either Mach3 or CNC
So I did what everyone always suggests I update my version to the newest online R3.043.066
Well I didn't realize it but I had to reconfig my Mach3. Well after getting everything to work as it should . I again reactivated my probe and looked for Probing 3d-digitising-Fenerty-Barker-Version-2.00.046. Still not present.
Still didn't give up I knew I had seen it somewhere so I checked my downstairs computer where I had downloaded and not registered the software and there it was same version as mine had been but with pugin?
I than went into Mach3 folder and Plugins found prog dll application put it on my thumb drive went upstairs and copied it into the plugin file up there
Yes when I went to Config plugins it was there I checked it and it now says Probe right beside Help.
I than go and click on probe a secondary screen comes up under x and y i enter the size of my item(assuming that is what it wants as it has to find center)
I turn off Machine cord and zero x and y axis
I than lower z until it is close to the highest point of material slow jog right down
I go to Diagnostic screen and slowly lower z until the green light comes on under digitization. I do this couple times and zero it just as it makes contact
I than raise tip so probe is not active
my setting in dialog box are:y x axis size of item 3x4 (All inches)
Max grid Incr tried at 1 default but now .25
Probe depth .125 deepest part of item
Probe clear .05
Probe rate 60 default don't know what it is?
diam 0 read doesn't matter
z for stuck probe 1.05
I than hit start , move probe shows active, and than finally yes
Probe moves to center stops say seq not complete. I hit reset and it moves does it again and again never completes
When I try inside diameter absolutely nothing happens
Somebody please help!!
Thank
Henry
Figured I had it cased
Here goes I installed the probe that came with my unit:
went to Config Port and Pins Input selected auto and it found it 1 13
Next I went into Config Config pugins looking for Probing 3d-digitising-Fenerty-Barker-Version-2.00.046. It wasn't there!
I than checked my Mach3 version number and it was R3.043.022
I was using older version installed it sometime ago than got sick and never got to set up or use either Mach3 or CNC
So I did what everyone always suggests I update my version to the newest online R3.043.066
Well I didn't realize it but I had to reconfig my Mach3. Well after getting everything to work as it should . I again reactivated my probe and looked for Probing 3d-digitising-Fenerty-Barker-Version-2.00.046. Still not present.
Still didn't give up I knew I had seen it somewhere so I checked my downstairs computer where I had downloaded and not registered the software and there it was same version as mine had been but with pugin?
I than went into Mach3 folder and Plugins found prog dll application put it on my thumb drive went upstairs and copied it into the plugin file up there
Yes when I went to Config plugins it was there I checked it and it now says Probe right beside Help.
I than go and click on probe a secondary screen comes up under x and y i enter the size of my item(assuming that is what it wants as it has to find center)
I turn off Machine cord and zero x and y axis
I than lower z until it is close to the highest point of material slow jog right down
I go to Diagnostic screen and slowly lower z until the green light comes on under digitization. I do this couple times and zero it just as it makes contact
I than raise tip so probe is not active
my setting in dialog box are:y x axis size of item 3x4 (All inches)
Max grid Incr tried at 1 default but now .25
Probe depth .125 deepest part of item
Probe clear .05
Probe rate 60 default don't know what it is?
diam 0 read doesn't matter
z for stuck probe 1.05
I than hit start , move probe shows active, and than finally yes
Probe moves to center stops say seq not complete. I hit reset and it moves does it again and again never completes
When I try inside diameter absolutely nothing happens
Somebody please help!!
Thank
Henry
Figured I had it cased