Hello Guest it is March 28, 2024, 09:01:41 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - hornby chopper

Pages: 1
1
General Mach Discussion / can you save mach3 to flash drive
« on: October 08, 2013, 10:24:52 PM »
Hi every one

just wanting to know if you can download mach3 to flash drive then load file in to older xp computer.
the reason is i do not have anything but internet from cell phone and the old computer has only dial up modem in it.

2
General Mach Discussion / hardinge chnc 1 retrofit
« on: October 11, 2011, 11:47:32 PM »
Hi  every one  ihave a hardinge chnc 1 precsion  1986  i want to change over to mach3 but this machine has  air driven  collet,part shute, parting off tool and
tool changer it is 240 volt  3 phase . I have  researched and i think going to use some parts from cnc4pc but can any one tell me what   XML and  other softwear will be  needed to make this work.

p.s.   i can do the  wiring and  mechanical that is easy hard stuff is COMPUTER PROGRAMS plug and play is fine so please keep it simple thanks :'(

thanks for any help

3
G-Code, CAD, and CAM discussions / plung feed rate
« on: September 15, 2011, 11:12:54 PM »
Hi every one just a small question

is there any way to just type in one line of g code at the  begining of your program for  feed rate of  plung on z axis.

im using free mill and it only sets the plung feed at the same speed for  x and  y feed rate.

i dont wan't to have to gow through  all  96750 lines of  code to change  feed rates

any sugestions or opinion is a greatly welcome and thanks

4
General Mach Discussion / mach3 reload
« on: July 23, 2011, 10:36:00 PM »
Hi  my computer died and the memory cards let go  now i want to reload mach3 .
how do i go about reloading the the mach3 program from my cnc mill to desk top computer and get to load over the  demo .

the cnc mill has  mach turn on it  looks like a nice set up i would like to play with it at my desk

please try to explane in detail  my computer has xp on it

thanks all

5
G-Code, CAD, and CAM discussions / gcode for hood emblems
« on: July 20, 2011, 04:52:38 PM »
hi every one starting to have fun  with  the mill now  just wanting to know what every one is using for  bmp or jpeg to gcode .
i have  2 hood emblems pictures that i down loaded from the net and would like to see how well the mill would do .


thanks for any info

6
FAQs / mach3 file on my nm200
« on: July 05, 2011, 11:15:59 AM »
Hi every one great site and  i like mach so simple ( needed for me)
i was woundering if it is posable to copy the mach3 fileand license form my nm200 and install this file into the lathe that i am building up.
the reaseon for asking  it has lathe tool set on it and  i like the set up of it and i can't get the same set up to download from this site.

any and all help is welcomed


thanks

7
Share Your GCode / tub bending dies
« on: July 01, 2011, 09:50:30 PM »
Hi every one lots of great info here
my question is  dose anyone have gcode files for  doing one pc or split tube bending dies and doing this on a mill without 4th axis

i know i sean some where in mach to dow mirror of parts this would help on the 2 pc dies

what dose every one think

Pages: 1