Hello Guest it is September 29, 2020, 01:12:47 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - Holzwurm56

Pages: 1 2 »
1
PoKeys / Mach3 and PoKeys 57U?
« on: August 30, 2020, 12:50:36 PM »
Hello,
does someone use Mach3 with an external Controller PoKeys 57U on a three axis milling machine
or a plasmacutter? Works this successful?

Many thanks for every answer
Hans

2
LazyCam (Beta) / Lazycam Manual?
« on: February 23, 2020, 04:39:26 AM »
Hello,
can someone tell me where I can download a manual for Lazycam? I am to stupid to find it.
Many thanks for every answer

Hans

3
General Mach Discussion / Question about Motortuning
« on: August 10, 2016, 04:07:05 AM »
Hello,
I have a problem with Motortuning. When I change the pulselength from step and direction to 5 µS, save the axissetings, close the motortuning and reopen the motortuning the display shows 0 µS. I test it sometimes. What do I wrong? Is there an other way to change the pulselength? I use WinXp.

Thanks

Hans

4
General Mach Discussion / Problem with Spindle Speed Control
« on: June 13, 2016, 06:47:36 AM »
Hello,
I use Mach3Turn for Lathe with control about 2 printerports. In the diagnosticsmode i can see the indexsignal working, but in the manual or automatic mode the spindlespeed display shows allways zero. I have test this with a low and a high spindlespeed.
Have someone a idea what i made wrong?

Many thanks for your answer

Hans

5
PoKeys / Question for Mach3 and two MPGs
« on: April 14, 2016, 12:35:53 PM »
Hi,
I use a Pokeys 56U as external controller for Mach3 on my lathe. I have install two MPGs and in the Pokeys I/O status I can see both working. In the Mach3 diagnostics I see only one working and on the manual mode screen works no one. The working mpg is connected to pin 1 + 2, DRO101, the other is on pin 5 + 6, DRO102.
Does someone has an idea what is my mistake?

Many thanks

Hans

6
PoKeys / PoKeys and a Lathe
« on: March 11, 2016, 11:45:29 AM »
Hi,
I want to use Mach3 with Pokeys 56U and a lathe with two handwheels. I want to use the lathe with the handwheels in conventionell mode and with gcode files or wizzards in a automatic mode. My servo drives need a 5,-Volt enable, step and direction signal and gives a 5,-Volt output error signal.
Does someone use so a configuration too?
Has someone a sample configuration file?

Many thanks for every answer

Hans

7
Galil / Configuring input- and outputpins DMC-1765
« on: September 06, 2015, 08:02:35 AM »
Hello,
the DMC-1765 has 24 inputpins and 16 outputpins . In Mach3 I find only 4 inputpins . In what kind of way can I configure the I/O pins under Mach3? In the Galilmanual I see softwarecommands SB , CB , AI and so on. Are there Machcommands like the Galilcommands? Can I use SB , CB in the gcode to control machinefunctions?

Many thanks for every answer

Hans

8
Screen designer tips and tutorials / Change Screen width
« on: September 24, 2012, 08:57:49 AM »
Hi ,
it's possible to change the width of a screen . The screen is smaller than my display , can I change the screen so that
the screen fills out the display ?

Thanks

Hans

9
PoKeys / Question about limit and homing switches
« on: September 18, 2012, 01:36:42 AM »
Hi ,
I am using pokeys 56u . My router has no extra home switch but end switches . It's possible like the Mach3 printerport mode to connect all endswitches
in one line and in reference drive mach3 recognice the endswitch as homeswitch and in working/milling mach3 uses the endswitches as endswitches ?

Many thanks for every answer

Hans

10
PoKeys / PoKeys connection to stepdrive
« on: September 17, 2012, 09:35:27 AM »
Hi ,
I use pokeys55u . It's possible to connect the pokeys directly to the stepper- or servodrives and endswitches or it's necessary
to switch a converter , optocuppler or other between the units ?

Thanks

Hans

Pages: 1 2 »