Topics

1

Brains Development / My Brain Needs Help!!!

« on: June 01, 2009, 02:54:22 AM »

I'm using a Pokeys analog input and while going threw a voltage divider it is very unstable..so what kind of code can one write to calm it down a little or other words buffer it.
Thanks for the help
Dave....

2

PoKeys / Analog not smooth

« on: June 01, 2009, 02:48:57 AM »

Borisz,
Would like to know if I have a problem....
When a pot is hooked up to pokeys the analog input on the test page is rock solid but when it is unhooked or hooked to my voltage divider it is unstable.
Is it the pokeys, the usb cable, usb port or pc ?
Has any one eles noticed this.
I'm using a brain to bring this to Mach..is there a way to calm it down in a brain???
Thanks Dave

3

General Mach Discussion / Help with torch up down

« on: May 11, 2009, 05:22:18 AM »

okay I have a problem...going through the brains on the torch up and down comand the Z axis is very jumpy.
also have up and down Leds on screen set with THC enable button & led and none seem to do anything...have not tried it with g code just on test bed...Maybe Scott AKA poppabear can help with this? if he has time...
If I use the shuttle All axis are smooth and liner....it is only when the brain turns on the torch up or down...
Thanks for any help
Dave

4

Mach SDK plugin questions and answers. / Can someone help me with this...Brian????

« on: October 03, 2008, 06:34:27 AM »

I'm going to reffer you to this thread
Thanks
\http://www.machsupport.com/forum/index.php/topic,8532.0.html

5

General Mach Discussion / shuttle pro outer wheel won't work...

« on: September 30, 2008, 08:13:20 PM »

Been using shuttle for some time and love it..but the other day I had a wire that shorted out and took out one of my drives, well long story short its all fixed and works again but the outer wheel wont work on the shuttle, I can go to the monitor screen and see it work.
I have deleted the dll file in the plugins and reinstalled with the latest version but it doesn't make any diff. so do any of you know what to try next. thank for the help.

6

Third party software and hardware support forums. / Have you had this problem??

« on: February 02, 2008, 07:34:15 AM »

The problem is that when I upgraded to the newest version of Mach my Soundlogic (campell break out board) profile locks up the PC when the PC starts the program...The Standard  profiles work just fine ..so I don't think there is any problem with the board. Any suggestions....

7

General Mach Discussion / G code loads wrong or missing parts!!

« on: June 18, 2007, 04:33:10 AM »

Last night I had a new project for the wife...(have lots of those) anyway I use Vcarve pro, when I loaded it in to Mach it doesn't read all the code right, (or transfer some of it) I go into edit or open it in notepad and the right stuff is there but it wont show up in Mach.(it gives me a line error...missing I, J, K. )  never had this problem before.
Just thought if any one had any insight to this, might save someone else a headach to.

This is the only problem I've had...Keep up the good work Brian Art ...And everyone on the forum...It's a great place to read and LEARN !!!!!!!!!

8

Newfangled Solutions Mach3 Wizards / problem with rec. hole pattern wiz. also

« on: June 04, 2007, 05:50:01 PM »

 My problem.. I'm trying to put holes .500 apart so I set the wiz up for 15 holes wide and 92 long 1" deep And all I get in gcode is some .500 moves in Y but the X is moving in .01 to .20  to all differnt moves....  Is me or the wiz.
Attached is the Gcode from the Wiz