Hello Guest it is April 21, 2021, 12:44:11 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - Thom2000

Pages: 1 2 »
1
Brains Development / Brain writing on/off relay
« on: November 18, 2018, 09:41:51 AM »
Hello,
I could use some help writing a brain.
I need to output a signal to a relay.
On when Z moves down and off when it moves up.
Any suggestions would be very helpful.
Thank you.
Mario

2
General Mach Discussion / Slave motor problem
« on: January 10, 2018, 07:08:55 PM »
Hello Groove-Guys (get it?),
I have a 4 axis machine with B as a slave to X.
The machine jogs correctly but when running a program the B no longer will run in tandem.
I've replaced the PC so that isn't it.
It ran fine before and jogs so I'd guess it's not a break-out board.
Any ideas would help.
Mario

3
General Mach Discussion / Screen4 additional buttons/images
« on: November 26, 2017, 10:38:44 AM »
Hello group,
It's been a long time (10 years) since I designed screens using screen4.
At that time there were extra buttons and images available for download.
I would appreciate any help in locating these.
Thank you in advance.
Mario

4
General Mach Discussion / Lazycam post processor line numbers
« on: July 08, 2017, 05:17:30 PM »
Hello,
Is there a way to manipulate the default post processor for Lazycam?
I need to eliminate line numbers.
Thanks in advance.

5
General Mach Discussion / Lazycam/ Cams
« on: April 17, 2017, 04:43:59 PM »
Hi folks,
A little off subject.
I need to drill 360,000 holes in a 13"x180" flat sheet metal part.
Lazycam does about 1/200th of this and any more freezes up the PC.
I use Lazycam for most everything so
I'm not sure of other CAMs.
Any suggestions would be appreciated.

6
General Mach Discussion / ZBrain writing
« on: April 14, 2017, 07:51:16 PM »
Hello Folks,
I need to write a brain that would activate a relay when the Z location is less than Z0.0
Any help would be much appreciated.
Thank you in advance

7
General Mach Discussion / USB to 25 pin break out board
« on: March 20, 2017, 11:39:30 AM »
The PC has a USB port.
The machine controller has a 25 pin break-out board  (C10).
Is it possible to run mach3 using a simple USB to 25pin lp1 cable?
I'm guessing there is more to it.

8
General Mach Discussion / Brain writing
« on: March 01, 2017, 05:02:59 PM »
Hello ,
I need to write a simple brain to trigger an output(1) using the Imput1 LED (821)  .

At the prompt to :

Do Nothing
Immediate   Compare  ETC
I'm not sure what action is needed to indicate the LED is on/off.
Any help with this would be greatly appreciated.
 I've watched videos and still am lost.
Thanks.

9
General Mach Discussion / Pin-out signal to activate button function
« on: August 18, 2016, 05:49:32 PM »
Hello Group,
I would like to activate the Single Block button in Mach3 using a 12v input signal.
Is this possible using a brain ?
Thank you in advance.
TC

10
General Mach Discussion / loading mach3 drivers /windows 7/ 32bit
« on: March 01, 2016, 12:21:58 PM »
Hello,
I can not load the drivers on an older pc running win7/32bit  After installing mach3 the set-up wiz says no drivers installed.
Any ideas would be very helpful.
Thank you.

Pages: 1 2 »