Hello Guest it is March 28, 2024, 09:59:39 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - riporeno

Pages: 1
1
VB and the development of wizards / macro for homing
« on: January 07, 2015, 05:24:12 AM »
hello everyone
I'm looking for a macro to do the 'homing as in professional machines. (with encoder)
I'll explain ...
the axis moves then when he hears the micro mechanical (input 1) reverses direction until it finds the zero mark on the encoder (imput2)
has anyone ever used this system?
thank you

2
*****VIDEOS***** / 4 axis machining anticorodal
« on: January 07, 2015, 05:00:49 AM »
hello everyone
place a video with the 4 axis of one of my latest work.
thanks to you all.
greetings

https://www.youtube.com/watch?v=0dcGpS-0vwU

3
Mach Screens / recall MPGmode with mause
« on: December 30, 2014, 08:02:36 PM »
hi
Normally to open the MPG mode use the TAB key on the keyboard.
I would like to create a button on the screen so you can click the mause
without using the keyboard.
I tried with scree4 but I could not find the command. ::)
Thank you that I can help.
regards
moreno

4
VB and the development of wizards / macro for start
« on: March 23, 2014, 05:06:07 AM »

hi to all
I frequent this forum just because I have to use the translator.
asking for your help to make a macropump.
I would make sure that when I push the start button, the machine starts to work only when it sees the signal input#1 ... (#2 or#3 etc etc)
Thank you.


http://www.cncitalia.net/forum/viewtopic.php?f=25&t=24799&start=135

5
General Mach Discussion / feedrate with the potentiometer
« on: February 13, 2011, 09:30:58 AM »
hi   :)
does the way exist for regulating the feedrate with the potentiometer? 
a card hardware can be built for this function? 
thanks 
regards 
moreno

6
General Mach Discussion / macro to force oupt
« on: February 10, 2011, 04:41:36 AM »
 hi to everybody  :)

as a macro can be made (example m300.m1s)  

what it forces an exit to 1(output #7) and another (example m301.1ms)  what does it to 0?  

the commanded signal, has to be also active after the reset
  
thanks  
  
moreno

7
hi   
I would like to insert in the g code the command that turns on the aspirator (m8) every 10 minutes for a duration of 5 minutes. 
This cycle is had to repeat for the whole program. 
How can I do? 
Thanks 
regards 
Moreno

8
hi 
I have to add a second lpt port breakout 
I would like to use the pins from 2 to 9 as imput. 
in this case as the remaining pins they work? 
pins 2-3-4-5-6-7-8-9 are imput 
pins 10-11-12-13-15 remain imputs? 
pins 1-14-16-17 remain outputs 
thanks 
regards 
moreno 

9
G-Code, CAD, and CAM discussions / G28.1 HOMING
« on: March 07, 2010, 03:30:55 AM »
hi   
I would like to make the homing with the gcode. 
I have written G28.1 but it doesn't work. 
Where am I wrong? 
thanks 
moreno

10
General Mach Discussion / safety spindle
« on: March 04, 2010, 02:40:29 AM »
hi to everybody. 
I am a new consumer. 
I am Italian and I write with the translator.  :-[
You won't understand well perhaps   
I don't succeed in resolving a problem. 
I should manage a signal of imput and to do so that when the signal is 0, (low) mach goes to emergency. 
This signal serves for checking that the pomp of rafreddamento of the spindle 
coop working. 
Then I would have need that once gives the command M3,mach holds me under control the imput#1 
In the case that this signal changes of state, mach has to go to stop and to stop the car. 
This control should happen only when it is active M3. 
Do you think can be done?   ::)
I don't know if I have made sense of, however thanks 
hi 
moreno

Pages: 1