Hello Guest it is April 24, 2024, 02:24:31 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Topics - sml

Pages: 1 2 »
G-Code, CAD, and CAM discussions / post processor 5 axis
« on: June 04, 2011, 11:09:03 PM »
Hi to all

I need a general(Fanuc,Mach3,...) 5 axis post processor for Powermill software by PMPOTS processor.

Please help me and sent a 5 axis post processor to below Email address :


Thank you

General Mach Discussion / DC spindle motor
« on: May 19, 2011, 07:12:56 PM »
Hi to all

I want use Mach3 for control a cnc machine with below specification :

Spindle : DC motor - permanent magnet - 400 watt  at 3600 rpm - 90 volt - 4 amper.

Axis motor : stepper motor - 5 phase - 10 wire - 16 kgf.cm - 1.4 amper.

What board do you suggest for control this spindle and axis motor? I don't know how can i control the spindle motor?
Can some one help me.
Does any board can control this spindle directly?

Please help me

Thank you

Mach SDK plugin questions and answers. / Plug in
« on: August 17, 2010, 03:00:33 AM »

I have a PCI1240-U Advantech board  but Mr.Hood in mach forum told me that i need to write a plug in for this board but i don't know what is plug in and how can i write it.
I don't have enough information about this board like wiring map or software adjustment.
Can someone help me please.

Thank you

General Mach Discussion / PCI-1240U
« on: August 16, 2010, 08:09:46 AM »
Is someone know or use PCI-1240U(http://www.advantech.com.tw) board?

Please let me know if some one used this board.
Thank you

General Mach Discussion / Spindle
« on: May 09, 2010, 06:23:52 AM »
Can anyone tell me , can i have a spindle pressure sensor for my milling machine by mach3 ?
What instrument i need for this ability on my spindle?
thank you

General Mach Discussion / Cutting speed
« on: April 30, 2010, 07:56:37 AM »
Can anyone tell me:
How calculate the cutting speed and rapid travels for cnc machines?
for example many milling machine have 24m/min speed for rapid travels and 1-10m/min for cutting speed.
Can i also use more than of 10m/min for cutting speed or not? Why?
Thank you

General Mach Discussion / Mach3 by Linux
« on: April 12, 2010, 01:34:09 PM »
Can i setup  and run mach3 on Linux ?
Does mach3 have any version for Linus?
Thank you

General Mach Discussion / Ballbar test
« on: April 12, 2010, 10:04:58 AM »
Does i need ballbar test for my cnc milling machine? or motor tuning is enough ?
Does i need ballbar test for using motor tuning?
Please tell me more
Thank you.

General Mach Discussion / RS232
« on: April 08, 2010, 10:47:23 AM »
Can i transfer a DXF file by RS232 cable from computer to another computer that has mach3 software ?
Thank you

General Mach Discussion / screen button
« on: March 24, 2010, 01:37:13 PM »
Please help me for screen button.
I design a new screen.set but i have a problem with jog button.In one page of screen the keyboard jog button ( page up and down for z axes) is working but in other page these keyboard button don't work.
What is the problem?

Thank you

Pages: 1 2 »