Topics

1

VB and the development of wizards / steps per by VisualBasic

« on: December 28, 2009, 11:56:34 AM »

Hi guys,

Is it possible to change the "steps per" ( Motor tuning ) with Visual basic ?

I would be very happy if this is possible.

With kindly regards from the Netherlands.

Riny

2

VB and the development of wizards / Wizards in Screen4

« on: December 14, 2009, 07:40:24 AM »

Hi there overseas,

I am trying to change a wizard in Screen4, but I can't see the bitmaps or jpg. Also when I use the Imagebutton to disable the images, I dont's see them.
What can I do for viewing the images?

Thanks from the Netherlands.

Riny

3

General Mach Discussion / Installation Mach3 3.042.032

« on: November 17, 2009, 07:28:59 AM »

Hi

On my computer was installed Mach3 version R3.037 and I have updated to version 3.042.032. But now I have a problem. When I want to edit my G-code, the editor starts up very, very slow and typing in the editior is also very slow. Saving etc.
Mach3 works further fine.

I de-installed Mach3, also the  Mach3 folder on the C drive and the the driver in the divice manager.

I have reinstalled Mach3 version 3.042.032, but the computer don't ask for rebooting. Is this normal, so the problems are still the same as before. Or are there still files, I have to delete?

Anybody knows what's going wrong?

With kindly regards from the Netherlands

4

PoKeys / Software don't see Pokeys

« on: November 04, 2009, 04:09:16 AM »

Hi,

I have 2 Pokeys55. The first one with firmware 1.97 en the second one with firmware 2.07
When I starts up the computer with firmware 1.97 the computer sees the Pokeys en the green led turns on.
With firmware 2.07 the green led don't turns on and Mach3 don't see the Pokeys.

I read on the forum that I am not the only one, but can't find what to do for fixing this problem.

Can I download firmware 1.97 and install this or is there an other solution?

With kindly regards
Riny ( The Netherlands )

5

PoKeys / Pokeys MPG

« on: November 01, 2009, 12:49:58 PM »

Hi guys,

I have setup a pokeys55 for one MPG. The encoder has 1000 ppm/rev.  If I turn the encoder very slowly, the the axis follows the encoder, but if I turn faster, the axis is missing many steps.
The same type encoder on the parrallelport in an other system works great.
Is it possible that the combination Pokeys and MPG works well, or do I something wrong?

With kindly regards from the Netherlands.

Riny

6

General Mach Discussion / Reverse X-axis

« on: October 25, 2009, 04:45:27 AM »

Hi guys,

On my lathe I use a turret and sometimes a normal toolchanger, so I need to reverse the X-Axis. "Homing / Limits / Reversed"

Is it possible to do that in Visual Basic or can I a make the state visible on the screen?

With kindly regards from the Netherlands

A happy Mach3 - User

Riny

7

General Mach Discussion / Feedrate override chage increase/decrease%

« on: September 01, 2009, 06:06:51 PM »

First of all, sorry for my English language, so I am from the Netherlands.

I have a problem with the Feed Override function in Mach3 Mill.

When I in-/decrease the value, it changes with 10% off the feedrate.
Is it possible to change this in 1%. For the spindlespeed you can change this in the general config, but I can't find this for the Feedrate.

I hope you can help me.

With kindly regards from the Netherlands.