Hello Guest it is October 04, 2022, 12:18:30 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - jonny quest

Pages: 1 2 3 4 »
1
General Mach Discussion / Cutting wrong dimensions in only one spot
« on: October 25, 2019, 01:14:56 PM »
Mach3, ESS Smoothstepper, Rhino5, Madcam.

I've tried backlash compensation on and off. Have my CV settings at .1, no other CV boxes checked. Tried IJ mode absolute and incremental. Talked with CAM developer about all settings.  Post is cutting with G2/G3. 

I've played with motor settings. Tried cutting at 1IPM.... I'm stumped.

Pic shows what's going on. Black shape is what I'm trying to cut. Red shape is cut part measured on CMM. I'm always getting this deviation at around the 10 o'clock position no matter what I try. The toolpath is correct, I really believe it's something in mach3

2
General Mach Discussion / Cut quality problem
« on: September 20, 2019, 11:59:18 PM »
Running Mach3, ess smoothstepper. Rhino drawings, madcam cam. When I run newfangled wizards cuts are nice and clean, through cam I get this. Any ideas?

3
General Mach Discussion / My spindle keeps shutting off randomly.
« on: February 08, 2015, 03:37:02 PM »
Running a ethernet SS, no rhyme or reason spindle will randomly shut off. VFD shows error of low voltage control.

Are there debounce settings in SS config... or any changes I can try in config to help?

When the issue is so random it's hard to trouble shoot

4
General Mach Discussion / backlash compensation in CAM
« on: September 29, 2014, 11:35:15 AM »
When I mill parts in Newfangled wizards they machine beautifully.

When I mill using my CAM package (Madcam) my 2d cuts are slightly rough.

I just had a thought. .. I'm using backlash compensation. .. is that not showing in my CAM post?

5
General Mach Discussion / driver needed for machining webcam
« on: March 16, 2013, 02:11:00 PM »
I purchased the machining webcam from CNC4PC, it says to just plug it in and driver will be found. My CNC computer isn't hooked up to the internet... and when I tried to plug it in on another computer I didn't have any luck.

I emailed CNC4PC, no response yet and I'm trying to get this running.

Anyone have a link or a driver I can download? Much appreciated.

http://www.cnc4pc.com/Store/osc/product_info.php?cPath=69&products_id=329

6
SmoothStepper USB / backlash comp, debounce settings
« on: March 04, 2013, 02:26:22 PM »
Does the ESS grab them from Mach... or do you need to enter those values in the ESS window?

7
when you hit the spacebar for feedhold, it is very slow to respond. I didn't count... but probably 2 seconds.

BUT... when you hit cycle start after feedhold... my A axis starts moving... even though I have no A axis commands in this G code!

I'm using an IMach USB pendant. So far when I jog with the keyboard... everything seems fine.

When I use my IMach USB pendant... small .001" steps seem fine. When I spin the wheel for distance travel... it doesn't stop! I also have to restart Mach to get it to stop! When I hit the estop to stop it from traveling... and then turn estop back on it's like the move is in que and keeps going until Mach is restarted.

I'm using latest ESS driver, latest Imach driver, and Mach .066

8
SmoothStepper USB / ESS installation help before I break something!
« on: March 03, 2013, 03:17:07 AM »
I hooked the ESS up... and have been going through the installation. Everything has been going ok until this box pops up....

***I did not connect this to CNC machine. I was just installing this before I hooked it up to my machine. I don't know what I should click here? I'm afraid to mess up any settings!***


9
Downloaded Mach3 .66 on new computer.... then tried copying old XML, and put it in the Mach3 folder.

That didn't work... none of my old settings are in the new computer.

I then copied complete Mach3 folder from old computer... put it in new computer... still no old settings.

Why isn't my old XML taking? What causes that?


10
SmoothStepper USB / where to mount the Smoothstepper?
« on: February 28, 2013, 05:52:59 PM »
I just purchased the ESS. Where are you guys mounting your boards?

In the computer itself? CNC control cabinet? Or just laying out in the middle of both computer and CNC cabinet?

Pages: 1 2 3 4 »