Hello Guest it is September 29, 2022, 02:36:25 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - mrpeja

Pages: 1 2 3 4 5 »
1
General Mach Discussion / Mach Z Axis dangerous behavior
« on: September 09, 2018, 11:34:50 AM »
Hi,
Forget to say, Windows XP is installed in ACPI mode
mrpeja

2
General Mach Discussion / WIN XP Optimisation
« on: September 04, 2018, 03:39:50 PM »
Hi,
I tried to optimize XP on Asus P5KPL-AM SE Mainboard and have plenty problems.
Question: Is it necessary to do this on newest mainboards?
What really we get?
mrpeja

3
G-Code, CAD, and CAM discussions / Mach1 mill misses to drill holes
« on: March 22, 2015, 04:41:51 AM »
Hi,
I have iregulary issue with my mill under Mach1. Sometimes it skips to drill some holes in the file and continues  to drill the others. When I check the drill file (looking at the listing) or with CNC viewer, all is ok.
So, I cant find where is the problem.
Any help will be appreciated.
Mrpeja
There is a segment of drill file:

(Created 21-03-2015 15:10)
(ISO G-Code - Non Modal)
(Drill diameter 1.09 mm/0.043")
M3
G90
N0001 T06 M06 S15000
N0003 G81 X1.981 Y4.1 Z-0.2800 R0.0500 F12.00
N0005 X2.121 Y4.1
N0007 X1.971 Y4.575
N0009 X1.971 Y4.666
N0011 X1.971 Y4.757
N0013 X0.946 Y4.8
N0015 X0.946 Y4.9
N0017 X0.747 Y5.475
N0019 X0.747 Y5.675
N0021 X1.32 Y6.05
N0023 X1.32 Y6.25
N0025 X1.23 Y7.28
.
.
.
N0569 X10.971 Y11.6
N0571 X14.421 Y11.6
N0573 X14.721 Y11.6
G00 X0 Y0
M05
M02
M30

4
General Mach Discussion / Stand alone THC
« on: June 24, 2013, 04:59:44 AM »
Hi all,
I'm planning to build plasma table for thin steel sheet (2 mm max) and I need recommendation for stand alone thc.
Any advice will be appreciated, possibly cheap.
Mrpeja

5
General Mach Discussion / SmoothStepper and THC
« on: December 24, 2010, 09:48:48 AM »
Hi,
As I can see on forums, SmoothStepper doesn't support THC function on Parallel port 2.
Is there any solution if someone want smooth stepping without parallel ports?
Many new mainboards haven't good results on Drivertest.exe, I think because of the SMI function.
Regards,
Mrpeja

6
General Mach Discussion / Mach Working hours
« on: November 16, 2010, 01:49:31 AM »
Hi guys,
I want to calculate how much my plasma table was used per month. Maybe some one has a solution?
I'll be gratefull
Regards,
Mrpeja

7
General Mach Discussion / Possible error in Mach3 ver. 040 ?
« on: July 28, 2010, 12:26:53 PM »
Hi Brian and all,
Last days I experienced a serious problem with Mach3 version 040. Very often one axis on my plasma table stops moving without visible cause. I discovered weird changes in Settings\motor outputs. Instead of my settings here appear mostly pin 0 as step output pin and sometime another  number. I correct this and axis works for some time but stops again.
Then I correct settings and push Reset button to blink and wait some time. Pin settings is changed again!
After this I installed older  038 version but the problem remains.
I solved this situation by uninstall and completely delete Mach3 folder, and then install again ver. 038. Now is vorking fine.
But I still don't know why this happens. Maybe is a bug in ver 040 and maybe I missed something?
Regards,
mrpeja

8
General Mach Discussion / Driver test AGAIN!
« on: July 16, 2010, 01:21:54 PM »
Hi,
I have read all about driver test and problems with PC hardware on forum.
I'm wondering: How big Max Variation should be and not to disturb Mach3 work?
I have new mainboard and get Max variation of 30 uS. Is this good  enough or bad for plasma table?
Regards

9
General Mach Discussion / Usefull macro for oxy fuel
« on: July 05, 2010, 03:02:31 PM »
Hi folks,
I'm two year experienced plasma table user. Now I want to reconfigure it for oxy fuel. I have read all I can find on the forum. There is more discusions and solutions, but I must admitt I'm not yet familiar with all this stuff.
So, please somebody to write all what is needed for one practical solution for oxy fuel cut.
Sorry for  my English
Mrpeja

10
Macros / Usefull macro for oxy fuel
« on: July 03, 2010, 03:09:12 PM »
Hi folks,
I'm two year experienced plasma table user. Now I want to reconfigure it for oxy fuel. I have read all I can find on the forum. There is more discusions and solutions, but I must admitt I'm not yet familiar with all this stuff.
So, please somebody to write all what is needed for one practical solution for oxy fuel cut.
Sorry for  my English
Mrpeja

Pages: 1 2 3 4 5 »