Hello Guest it is December 04, 2020, 07:10:42 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - francopuk

Pages: 1 2 3 4 5 »
1
General Mach Discussion / Mach4
« on: October 28, 2013, 01:14:15 PM »
hi to all, exist one data for distribution of Mach4 ?
thank
Franco

2
General Mach Discussion / Re: ERROR B109-11
« on: April 29, 2008, 12:46:35 PM »
THANK YOU CHIP.... ALL OK

3
General Mach Discussion / ERROR B109-11
« on: April 14, 2008, 03:54:09 PM »
HI TO ALL, I HAVE DOWNOLADED R3.041 AND RUNNING THIS SETUP RETURNED AN ERROR B109-11 "cannot decompress setup program" ANY IDEAS IS WELCOME
thank in advance for your help
Franco

4
General Mach Discussion / Re: LAZYCAM MACH 1.84
« on: October 16, 2007, 12:12:08 PM »
hi Hood, no i search the LaziCam program for running with Mach3 release 1.84
Franco

5
General Mach Discussion / LAZYCAM MACH 1.84
« on: October 15, 2007, 05:21:44 AM »
Hi to all, i search the LazyCam for Mach3 v. 1.84 if you have this,
please inform mi
thank in advance
Franco

6
General Mach Discussion / QUESTION
« on: September 14, 2007, 05:43:00 AM »
HI TO ALL, IN THE RELEASE R2.42 ARE PRESENT THIS GRAPHICAL UTILITY:

- DOUBLE CLICK IN THE GRAPHICAL WINDOWS PROJECT THE PICTURE IN ORTOGANL MODE.

IN THE RELEASE R2.45 THIS UTILITY ARE NOT PRESENT
THIS IS NORMAL ?

thanks in advance

Franco

PROBLEM IS SOLVED WITH RELEASE 2.46..... TANK FOR WORK

Franco

7
General Mach Discussion / Re: DRO not 0
« on: July 29, 2007, 02:49:31 PM »
Hi Williams, i not find "Setting screen" in the menu... i resolve problem in the SETTING FIXTURE
with cleared the value present in the G54 cell X and Y
Thank for help
Franco

8
General Mach Discussion / DRO not 0
« on: July 22, 2007, 01:13:54 AM »
HI to all, my MACH3 rev R2.02.00 report on DRO
X-2.5500
Y-3.4420,
i have UN-CHECK "PERSISTENT DRO" this not resolve problem
i check in the "Setting alt6" and the value is reported in "ENCODER POSITION
X-2.5500
Y-3.4420"
i have click on ZERO
the value return
X-0.5500
Y-0.4420.
at next run MACH3 return the primitive value
X-2.5500
Y-3.4420,
WHAT IS THE ERROR?
I NOT USE ENCODER....
Any ideas for resolve this problem is WELCOME !!
thank in advance
Franco

9
Italian / Re: Italian Screenset
« on: June 08, 2007, 02:47:19 AM »
Ciao Bul
in mach3 รจ presente una utility che si chiama lazycam, la trovi nel menu a tendina file
da qui puoi elaborare i file dxf, non conosco il gerber per cui non ti posso essere utile,
nel caso ne venissi a capo puoi informarmi sul da fare?
grazie
Franco
i4puk.franco@alice.it

10
General Mach Discussion / Re: PROBLEM WIT LAZY CAM
« on: June 01, 2007, 07:38:41 AM »
THANK FOR REPLY, THE PROBLEM IS THE DIMENSION OF FILE, IF FILE IS < 100K THE WORK IS CORRECT
IF GREATHER 500K AFTER 10" OUT MESSAGE "lazycam not responding"
MY PC IS P4 1,6MHz AND 512 MB RAM
Franco

Pages: 1 2 3 4 5 »