Hello Guest it is April 14, 2021, 11:14:04 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Bengt

Pages: 1 2 3 4 5 6 »
1
Newfangled Solutions Mach3 Wizards / Re: NFS Turn Wizard
« on: July 07, 2012, 01:42:07 PM »
Hi Ron,

Thanks for the update, will try to run this tomorrow on my lathe so I can report back.

Cheers
Bengt

2
Newfangled Solutions Mach3 Wizards / Re: NFS Turn Wizard
« on: June 08, 2012, 04:20:50 AM »
Quote
One IMPORTANT request, there is no manual jogging via keyboard so I really want to push on this upgrade asap to have this wizard fully functional.

Hi Ron,
Have you had a chance to look at this?

Cheers
Bengt

3
Newfangled Solutions Mach3 Wizards / Re: NFS Turn Wizard
« on: April 27, 2012, 03:45:25 PM »
Hi Ron,
Went down to my workshop and loaded the wizard in my lathe, as you can see it fit well and is readable in 12" 800x600 resolution.
However if I need to do any configuration at far righthand side I need to have another screen, I wish those pages would be AUTO-SCALING too.

One IMPORTANT request, there is no manual jogging via keyboard so I really want to push on this upgrade asap to have this wizard fully functional.

Cheers from Sweden
Bengt

4
Newfangled Solutions Mach3 Wizards / Re: NFS Turn Wizard
« on: April 26, 2012, 04:58:20 PM »
Hi Ron,

This reminded me to tell you that I use 12" monitor with touch screen in 800x600



Cheers
Bengt

5
Newfangled Solutions Mach3 Wizards / Re: NFS Turn Wizard
« on: April 17, 2012, 12:24:09 PM »
Hi Ron,

I would like to chear in and say it is a very fine job you have done with the wizard. Having some requests, ID Thread and ID Taper as well as Tapers to have taper.txt so we can have pre defined tapers like MT1, BT40 etc

Cheers
Bengt

6
PoKeys / Re: What plugin to use for old 55?
« on: December 20, 2011, 12:01:05 PM »
So I hear, but many of us are not so lucky.

Single step and Multistep works OK.  Velocity Only and Step/Velocity does not work, can somebody please explain what the heck is going on.

Btw, today the Matrix keyboard works on the testpage so go figure what causes this behaviour.

Cheers
Bengt

7
PoKeys / Re: What plugin to use for old 55?
« on: December 20, 2011, 03:19:35 AM »
OK, the first is no longer supported  ???
The new one is far far away from ready  ???

So what do all PoKeys users do in the mean time? Play poker or what?

No really, there must be a way to get MPG to function with the old Plugin. Have to dig deeper into this....

Cheers
Bengt

8
PoKeys / Re: What plugin to use for old 55?
« on: December 19, 2011, 04:48:23 PM »
Thanks Boris,
found a file in c:/mach3/
Anyways that did not help much to setup 1 MPG - Matrix keyboard - LED matrix - LCD - 2 analog inputs and 1 digital input.

Went back to the old plugin, still I have problems with that one to. Yesterday matrix keyboard was OK in Mach3/Pokeys test page but not today.
MPG is OK in single step and multistep but *********s up in velocity and step/velocity. Not able to get anything OK in those two modes.

If I recall all this was functioning before way back, but why now all kinds of peculiar behaviour.

Everything is OK with Pokeys when test the functions (not LED test that is mirrored in X axis. Same in PoKeys screen LEDs are mirrored ( all connected to latest sample schematics in documentation)

MPG in Mach3 is very SLOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOW that we know but this slow?

Cheers
Bengt

9
PoKeys / Re: What plugin to use for old 55?
« on: December 19, 2011, 03:52:48 PM »
OK thanks Boris.

Is there any kind of documentation for Brians plugin?

Cheers
Bengt

10
PoKeys / What plugin to use for old 55?
« on: December 19, 2011, 03:00:51 PM »
Hi guys,
So I am back again with my toys and need som advise.What is the latest plugin to go with my old 55's?
Please take look at my site where I have some pictures and how my 55 is setup. http://www.93x57r.se/tecno-cnc/Mpg.html
Been looking around and I cannot get a clear picture of what plugin to use
so if you guys would help an old fart to get back on track with his project I would be grateful.

Cheers
Bengt
 

Pages: 1 2 3 4 5 6 »