Hello Guest it is September 29, 2020, 04:40:15 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - sanlee

Pages: 1 2 3 4 »
1
General Mach Discussion / Re: Problem in Turning after Threading
« on: March 24, 2009, 12:13:36 AM »
Ya Hood

you are absolutely right. instead of writing in M1076 i should make a practice to write in preamble. i will definately follow this. thanks again

sanlee

2
General Mach Discussion / Re: Problem in Turning after Threading
« on: March 23, 2009, 10:00:22 AM »
thanks hood

wel! i undserstood now. and now it revert back to G94 if the preamble has G94. Even one more thing i have tried and it works very nicely. i.e. i have written Code "G94" in M1076.m1s macro at the last line. so now there is no need to have G94 at preamble.

Thanks lot

sanlee

3
General Mach Discussion / Re: Problem in Turning after Threading
« on: March 23, 2009, 08:57:12 AM »
Thanks Hood

after writing G94 it works perfactly. But one more thing i want to know that is it possible to write G94 in some of the macro which is written for G76, so that operator need not remember to write every time G94 after threading code is over.

thanks again

sanlee

4
General Mach Discussion / Problem in Turning after Threading
« on: March 23, 2009, 07:38:56 AM »
 Dear All

I have designed 3-axis milling and also lathe both are working very nicely using Mach3. Now after a number trails of turning taken in lathe i observed one problem i.e. if i run G76 for threading, it works very nicely. but after that if run simple truning then it is not working correctly. e.g. my code is G01 z-20 F50. then z axis should move with the feedrate of 50mm/minute. instead of that it moves 2000mm/minute which is my rapid speed.
this problem remains as it is till i shut down mach3 and restart it. after restarting if i run simple turning job then it works perfactly. but again if i run G76 thread command then threading is Ok but after that it is not recongnizing G01 code and it always consider G00 and executes all command with G00 even if i mention G01. i have not use G32. and threading file is made from the simple threading wizard given in Mach.  kindly give the suggession on this.

thanks

sanlee

5
LazyTurn / Re: LazyTurn
« on: December 08, 2008, 07:02:30 AM »
Hi All

I have made one dxf file as attached to make inner side radius of 100mm in disk. when i opened in LT and generate toolpath it did not correctly but it created as shown in photo. Also i have tried to creat file in LCam then also it is not creating. i have drawn different types of files to creat inner radius or 100mm but fails. please help me what i have done is wrong? Also when i am closing LT it is showing an error as shown in Post390.

thanks

sanlee

6
LazyTurn / Re: LazyTurn
« on: December 04, 2008, 02:51:31 AM »
Thankyou HOOD, CHIP, RICH and other friends

My problem is solved by changing the mode i.e IJ  :). This is good learning with you all.

Thanks again

sanlee

7
General Mach Discussion / Re: Lazycam Turning Problem
« on: December 04, 2008, 02:45:16 AM »
Thank you RICH

When i change the IJ mode from Absolute to Incremental my problem is solved. and i have downloaded MACH V3.041 in this my file seems similar to what you have shown. Also see the attached dxf file as told by you.

thanks again.
sanlee

8
General Mach Discussion / Lazycam Turning Problem
« on: December 02, 2008, 01:10:49 AM »
Dear All

I have made one Dwg in autocad and opened in lazycam as turning job. i have licenced fir LC and Mach3. The problem is Gcode file generated by LC is not opening in the Mach and showing "Radius to end of arc differs from radius to startLine 29" this error. i am attaching some of the photos with test.tap file. can any body tell me why this is happening.

Thanks

sanlee

9
LazyTurn / Re: LazyTurn
« on: December 02, 2008, 12:25:36 AM »
RICH,
sorry to say you that i have tried the file in diameter mode and reversed arc's unchecked but still there is no improvement in result. Also i have updated Mach3 R3.04 and opened the same file but still result is same as shown in below photo. i dont know what is wrong with my side.

sanlee

10
LazyTurn / Re: LazyTurn
« on: December 01, 2008, 07:05:37 AM »
Thanks RICH

I did check and uncheck both in "Reversed Arc's in Front Post" located in CONFIG>PORT&PINS>TURN OPTIONS. but still result is not getting. where should i wrong i dont know. please any further suggessions?

sanlee


Pages: 1 2 3 4 »