Messages

1

General Mach Discussion / Re: Mach 3 won't jog with keyboard

« on: September 01, 2007, 09:20:12 AM »

I deleted the jog button right of the bat, except on the diagnostics page , and it was jogging fine, I will try that , but what started it that I wanted a toggle for fast and slow jog like the shift key but on the screen, than I found the slowjog increase and decrease buttons and added them to the set up screen, thats when it stopped jogging with the keyboard, so I think its something else, especially since the jog on button never worked on the screen anyways

Turns out You right You have to have a jog button on the page for the keyboard to work.

That;s it .... got everything but the oem code for the shift key....anybody know?

Thanks
   Frank

2

General Mach Discussion / Re: Mach 3 won't jog with keyboard

« on: August 31, 2007, 08:35:03 PM »

The one thing I like to change , on the set up page remove the stop button in the jog section and substitude for the shift button, so I be able to toggle between fast and slow jogging, but what is the oem code for the shift button?

3

General Mach Discussion / Re: Mach 3 won't jog with keyboard

« on: August 31, 2007, 08:32:28 PM »

That did the the trick .....thanks

Anyways see what You think

4

General Mach Discussion / Re: Mach 3 won't jog with keyboard

« on: August 31, 2007, 08:16:41 PM »

I thought I be able to attach the file but how do You do it?

5

General Mach Discussion / Re: Mach 3 won't jog with keyboard

« on: August 31, 2007, 08:02:34 PM »

No that ain't it either, it will jog on the screen but not with the keyboard, if it is set to mpg it won't jog on the the screen, I also tried restting the hotkeys even though it already shwed the right numbers, I will try to post the screen set You can give it a try and see if You can get it to work.

6

General Mach Discussion / Re: Mach 3 won't jog with keyboard

« on: August 31, 2007, 07:55:28 PM »

No I checked that , I using Ver 2.2 and working with the simple 3 axis screen, also when I load a different screen the keyboard buttons work.

7

General Mach Discussion / Mach 3 won't jog with keyboard

« on: August 31, 2007, 07:16:18 PM »

Hi,
I'm been playing with the screen and now just as I get everything the way I like it, the keyboard won't jog anymore, it will still jog with the touchscreen , but not with  the keyboard.
Just to be sure I opened the editor and the arror keys move the tap around, so its not the keyboard, when checking the hot keys they are all set aswell....

Any ideas

Thanks
   Frank

8

Mach Screens / Oem Code for Shift Key

« on: August 31, 2007, 08:42:48 AM »

Is there an Oem Code for the shift key?
Thanks
  Franki

9

Mach Screens / Jog Rate Override

« on: August 30, 2007, 05:38:17 PM »

Is it possible to apply the feedrate override to the jog rate, so that there would be a button that applies the lowered feedrate also to the jograte and an led that inticates that you are jogging at the lower rate set int the feed rate override?

I'm working with the simple 3 axis screen and the only way to jog in continious mode is full bore.

I created a button and tried oem code 287  rapid override but it doedn't affect the jog rate neither does oem 202 feed override jog whatever that means.

Thanks for any help

Frank
 

10

Screen designer tips and tutorials / Re: OEM Code

« on: August 29, 2007, 09:23:00 AM »

Scott,
This is great, got it to work on the simple 3 axis screen and decided to try also resetting the the counter when I close out the G-Code, since I don't think that I hit the reset button everytime I change programs, so I added this code to the close gcode button

SetUserDRO(1230,0)
DoOEMButton(169)

And it works, I think I'm getting the hang of it.

Thanks Again for posting that
Frank