Hello Guest it is March 29, 2024, 01:28:52 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - adamfromscotland

Pages: 1 2 »
1
General Mach Discussion / Re: *** FORUM SEARCH FACILITY BROKEN ***
« on: January 04, 2019, 10:40:12 AM »
thats why i posted my new question as doesnt work

2
General Mach Discussion / Re: Motor Tuning doesnt Open up in mach3
« on: January 04, 2019, 07:55:19 AM »
Hi

No the <a href="http://driver is the correct one" target="_blank" rel="noopener noreferrer" class="bbc_link bbc_flash_disabled new_win">http://driver is the correct one</a> and was working okay before!

and just reinstalled it

Though i noticed it was plugged into a RED Usb Socket and have since plugged back into a USB 3 blue port!

https://youtu.be/jU6MA85nJgU

does anyone else know why its not working?????????

3
General Mach Discussion / Re: Motor Tuning doesnt Open up in mach3
« on: January 04, 2019, 03:59:56 AM »
Thanks for replying

I dont think anything has been changed!

I used to have the v1 version of the BOB but now have the V2 buhink the v2 was installed so no other thing has been changed!

It just fails to open up Motor Tuning and all other items work in the mach 3

My motors were Axis Calibirated set steps per unit okay in MM

But now my Nema 23s move very slowly, so i was thinking i now have to beef up the speed in them??

But tried via the motor tuning but it doesbt open up?

Ive restarted the PC and also the System still doesnt work!

Does anyone know why this Motor Tuning doesnt open up???

4
General Mach Discussion / Motor Tuning doesnt Open up in mach3
« on: January 03, 2019, 03:58:15 PM »
Does anyone know why all the settings work and open up

But

Motor Tuning will not open up the dialougue box?

All other settings open up

Im using Windows 10 64 bit with version R3.043.066

and the BOB is a NVUMC Version 2? :)

5
 ;D
Thats a jolly good reply Rojer

Im familiar with Momentary switches as bought lots from ebay but mainly 240v ones, but i may have or will buy some smaller say 24v ? Momentary switches?

Where abouts would you put that switch? next to limits?


Thats a really good idea, does this work? did you try/do it? or has anyone else done this with there limit switches?

Ive never heard off this before but kind of make sense :)

Will go to Rs or ebay and look for some

6
Anyone use the  CNC Breakout Board Mach3 CM-202 Parallel  Board?


7
Ive since done some research and it seems dodgy my BOB via Mach3 with SoftLimits also!

Seen some commenets in youtube video!
 :(

Will look into a new BOBBY Soon

Thanks!

I will let you know if my new BOBBY works!

8
Are you associated with "CNC DRIVE" ?

Anyone else know why the limit switches dont pull off from the hard limits?

9
Im Starting too think this myself, I wonder whats a suitable alternative? thats not crazy in price that goes with my other bits?


Im also thinking a lot to do with it being a USB model

10
 ???I did not think photos would help as was hoping someone could just tell me what i was doing wrong but a piccie says a thousand words

My BOB is a Nvem CNC USB Output board!

and limit switches are Osisense ones they work okay though but nothing works!

my controller box is all wired okay i think still grounding to do, but my limit switches are fine and i dont get random emergency stops,

Its just i can move off the hard limits, osisense switches after ive hit them, the mach3 says Reset but no matter what i do it doesnt reset!

Pages: 1 2 »