Messages

1

General Mach Discussion / Re: "Software Limits" in Status during Ref All Home

« on: June 20, 2018, 04:56:07 PM »

Ohhh. so you think... that is the problem???

2

General Mach Discussion / Re: "Software Limits" in Status during Ref All Home

« on: June 20, 2018, 04:38:05 PM »

I thank you Bryanna for your reply. I am going to Test it in the way you said. However, just to let you know that in the diagnostic page .. I found "M3 ++ LIM" light is Yellow red. Does that mean that something wrong with the motor as well???

I tried to down load Mach3 from one of my friend's comp. to one of my new machine with Windows 7, that also has parallel ports.... I have written the exact config. from the past so exactly copied after downloading and connecting to the new computer with the fresh down load of Mach3.. but Alas! same result it said Emergency External Estop requested again. Now one thing is different on the new one is once I click Clear and Reset it again it said, Limit Switch Triggered.... Does it give you and twist on the situation. Please consider this too and let me know if you can. I would rather go with my old Mach3 and old comp. machine than with the new machine...... As you know my email address so you can feel free to email me as well.

Thanks again

Faisal
visualletters5@gmail.com
 

3

General Mach Discussion / Re: "Software Limits" in Status during Ref All Home

« on: June 18, 2018, 04:47:34 PM »

there you go again.

4

General Mach Discussion / Re: "Software Limits" in Status during Ref All Home

« on: June 18, 2018, 04:46:06 PM »

BRYANNA: I tried to send you the file in the Reply.. .but it is giving me an error by saying it has already been submitted.. Have you got it. ?

5

General Mach Discussion / Re: "Software Limits" in Status during Ref All Home

« on: June 18, 2018, 03:32:00 PM »

Thx for yr reply.

I did that but the Estop display gone however, the spindle (jog) is not moving only the numbers on the screen moves when I move with my keyboard arrows. so it didnot work ...

I really appreciate that you are taking interest in fixing my problem.. I really really need it. THANKS>

6

General Mach Discussion / Re: EXTERNAL ESTOP REQUESTED

« on: June 18, 2018, 01:36:55 PM »

I am useing Mach3 X.X ... that is what it says when it start up. I dont know how to search for a .xml file and copy from there..

7

General Mach Discussion / Re: "Software Limits" in Status during Ref All Home

« on: June 18, 2018, 01:35:32 PM »

I have mentioned my Mach3 problem in another session as well.. however, by googling I got this page so I am mentioning here as well.

To, HIGHSPEED & Others: The External ESTop is on and by clicking Reset it is not going away.. .also I just check that on the Diagnostic Screen my M3++ LIM light is Yellow, ON. Is it because I might move the Jog manually a little bit or for other reason..... .How can I get rid of it. Any suggestion?

8

General Mach Discussion / Re: Configuration problem with EStop

« on: June 18, 2018, 11:57:56 AM »

Thank you Bryanna, I dont know my last you got it or not. BUt can you please send me the details for the NEW Mach4 licensed software info on my emai: Visualletters5@gmail.com.

I thank for your advice and looking forward to it.

Faisal
Visual Letters
Cell: 832-868-5426
Email: visualletters5@gmail.com

9

General Mach Discussion / Re: Configuration problem with EStop

« on: June 18, 2018, 11:55:32 AM »

Thanks Bryanna and Craig both for your prompt reply and suggestion, I really appreciate it.

However, today I insert the missing USB back to the CPU and it does not work.
CRAIG: the Driver Test file you asked me to run ... I don't know how to run that .exe file on my cpu...can you pls guide me.. Also Yes, I am using a serial cable on this machine . ( I don't know what was that USB for but it was there since I had been running the machine and the moment my software issue arise I took it out and forgot to insert it back, as I said today I insert back again but nothing made a difference).

10

General Mach Discussion / Re: Configuration problem with EStop

« on: June 17, 2018, 11:45:47 PM »

I am also new to Mach3, and am experiencing the same problem.

I runs XP and is ONLY connected to the router.  Originally, I could not get the Reset button to reset the system. Hitting the Estop did not help... I tried everything but nothing seems to work. I tried to make Active Low in Ports and Pins but the Estop sign gone however, now the Job is not moving physically but only the numbers moving on the screen in Mach3... Please suggest

Faisal from Houston
visuallletters5@gmail.com