Hello Guest it is March 19, 2024, 06:08:56 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Aussie John

Pages: 1 2 »
1
General Mach Discussion / Re: KX1 with Mach3 not talking to computer
« on: September 23, 2017, 10:40:46 PM »
Hello Craig
Just tried the estop on the mill when pressed another LED comes on inside.
John

2
General Mach Discussion / Re: KX1 with Mach3 not talking to computer
« on: September 23, 2017, 10:18:06 PM »
Hello Craig
Where do I find Limit and home switch?
The spindle is in Motor Outputs not outputs in my Mach3. Went into  Motor outputs and disable Spindle.
Digt Trig now disabled
in input signals made X++ Pin number 10 and X- made pin number 13.are input pin the same as Port#?
Craig all the numbers and enables were generated in con/fig when we down loaded Mach3 vision .062. when the old computer hard drive crashed and had to reload Mach3
It is running in demo mode, have asked Mach support for our licence numbers and how to change to licenced mill.
I must have nearly drove you to the drink with all these questions.
Thank you
Craig
Cheers John

3
General Mach Discussion / Re: KX1 with Mach3 not talking to computer
« on: September 23, 2017, 08:03:08 PM »
hi

4
General Mach Discussion / Re: KX1 with Mach3 not talking to computer
« on: September 23, 2017, 07:58:59 PM »
hi

5
General Mach Discussion / Re: KX1 with Mach3 not talking to computer
« on: September 23, 2017, 07:57:21 PM »
hi

6
General Mach Discussion / Re: KX1 with Mach3 not talking to computer
« on: September 23, 2017, 07:54:35 PM »
hi Craig


7
General Mach Discussion / Re: KX1 with Mach3 not talking to computer
« on: September 23, 2017, 02:33:43 AM »
Hello Craig
The computer running the mill has no internet connection. We were told not to.
Have taken photos on my Ipad of the first four of the con/fig ports and pin, taken photos of the test with the start long signals and other through the test.
Taken the sides off the mill and taken photos of all the inside, quite a few LEDS working, pressed the keys on the key board and the lights never changed /blinked.
Turned off mill and the reset button started to flash and would not stop, asking for external reset. turned mill back on and the restart on the computer would turn off.
Sorry Craig, pretty old (71) and have trouble understanding some of the things.
Cheers John 
 

8
General Mach Discussion / Re: KX1 with Mach3 not talking to computer
« on: September 23, 2017, 12:41:00 AM »
Craig
On the start of the test the two lines from top to bottom are reading between 2675 to 9.318 and 365.943 to 370.325
Cheers John

9
General Mach Discussion / Re: KX1 with Mach3 not talking to computer
« on: September 23, 2017, 12:30:32 AM »
Hello Craig
The reset on the computer will change through key board. . The estop on the mill will not set the reset on the computer to flash.
Ran test again and on the start there was two lines close together they were from top to bottom 0 to 80 then there was other lines above line just under 48.
Pulse 2499. Max variation 5008 to 7.183, short 38.44, long 44.12Apic control 7995. CPU 3000, CPU MHL 300, version 601, PCI 3000
Craig the new Mach loaded is showing Demo. We have bought a Mach3 licence and have the machine serial and manual serial numbers they supplied with mill.
Being in Demo mode would that change anything?
Thank You Craig
Cheers
John

10
General Mach Discussion / Re: KX1 with Mach3 not talking to computer
« on: September 22, 2017, 10:49:53 PM »
Craig
went back out to the mill and the test is now over and it is saying System Excellent.
Sorry I don't no how to post a screen shot.
Cheers John

Pages: 1 2 »